Forced Induction

506 topics in this forum

1. Doing some turbo build research, best/easiest engine to use 1 2

   By Jpich85, December 7, 2020
   • 25 replies
   • 2.2k views
   • 
   • meisseli
   • December 12, 2020

2. Engine prep for turbo build

   By rerb, December 10, 2020   

   • turbo
   • prep
   • (and 2 more)

     Tagged with:

     • turbo
     • prep
     • bottom end
     • ape
   • 7 replies
   • 885 views
   • 
   • rerb
   • December 11, 2020

3. GSX400 turbo-project 1 2

   By JJSalo, November 6, 2020
   • 36 replies
   • 3.7k views
   • 
   • zed
   • November 25, 2020

4. XN85 Turbo

   By Peterrr, November 7, 2020
   • 13 replies
   • 1.5k views
   • 
   • Screwriverracing
   • November 11, 2020

5. newbie with a efi setup question 1 2

   By mrutah12, September 1, 2020
   • 29 replies
   • 2.9k views
   • 
   • mrutah12
   • November 1, 2020

6. Bandit 1200 Turbo EFI can't get out of it's own way 1 2 3

   By rider384, October 5, 2020
   • 57 replies
   • 6.5k views
   • 
   • rider384
   • October 30, 2020

7. Clutch slipping?

   By Reinhoud, August 30, 2020
   • 9 replies
   • 989 views
   • 
   • Reinhoud
   • October 24, 2020

8. About time to!! 1 2 3 4

   By Screwriverracing, April 10, 2016
   • 95 replies
   • 12.1k views
   • 
   • Screwriverracing
   • October 4, 2020

9. barrel advice for a 1216

   By stellafella, October 29, 2018
   • 20 replies
   • 3.9k views
   • 
   • Joseph
   • October 4, 2020

10. Carb Diaphragm Covers/Tops

    By Bobby, September 17, 2020
    • 2 replies
    • 480 views
    • 
    • Bobby
    • September 17, 2020

11. Throttle body spacing

    By slingy1157, April 20, 2016
    • 8 replies
    • 2.4k views
    • 
    • GSX1100dreamn
    • September 16, 2020

12. Fuel pressure and carb tuning on turbo GSXR

    By Baron, August 21, 2020
    • 3 replies
    • 2.3k views
    • 
    • Baron
    • August 28, 2020

13. Newbie with turbo setup Question

    By Turb, August 25, 2020
    • 3 replies
    • 1.3k views
    • 
    • Swiss Toni
    • August 26, 2020

14. Recommendation for fitting Hayabusa Pistons in to a B12

    By Brians 7/12, June 11, 2020
    • 3 replies
    • 969 views
    • 
    • Hoomietune
    • August 16, 2020

15. Plenum problems help needed

    By Mike750, July 29, 2020
    • 5 replies
    • 915 views
    • 
    • colinworth79
    • August 11, 2020

16. Bandit 1200 turbo choice 1 2

    By BanditPervert, June 26, 2020
    • 30 replies
    • 6.5k views
    • 
    • Reinhoud
    • July 4, 2020

17. Bandit 12 plenum

    By BanditPervert, April 30, 2020   

    • jkm46
    • 23 replies
    • 2.8k views
    • 
    • slabbyfaceddean
    • July 3, 2020

18. Draw through carb and carbon seal ponderings 1 2

    By Samikoo, April 14, 2020
    • 31 replies
    • 5.8k views
    • 
    • slabbyfaceddean
    • July 3, 2020

19. Turbo engine prep

    By BanditPervert, May 25, 2020
    • 21 replies
    • 2.9k views
    • 
    • Mark28
    • June 19, 2020

20. Boost controller

    By Reinhoud, June 2, 2020
    • 10 replies
    • 1.4k views
    • 
    • MeanBean49
    • June 4, 2020

21. Gsx1400 barrels

    By Hendo, June 2, 2020
    • 3 replies
    • 632 views
    • 
    • Blubber
    • June 2, 2020

22. Plenum finish 1 2

    By zedhead, May 4, 2020
    • 30 replies
    • 2.6k views
    • 
    • Kid Kearsley
    • May 26, 2020

23. pistons

    By Tombola, May 20, 2020
    • 5 replies
    • 859 views
    • 
    • Tombola
    • May 21, 2020

24. aftermarket Oil cooler

    By Bobby, May 17, 2020
    • 9 replies
    • 846 views
    • 
    • Bobby
    • May 17, 2020

25. Slingshot pump in tank

    By Mike750, April 22, 2020
    • 19 replies
    • 1.4k views
    • 
    • JK1
    • May 1, 2020