Brian

[gray711]

I’ll check my hoard of bits - may have a spare one but can’t quite remember. Not home till tomorrow & can’t promise anything so if one comes your way I’d say take it - there’s a couple on the bay btw

[fatblokeonbandit]

That would be excellent shipmate I’ll have a look a Eblag as well 

I have lots of stuff to swop 

[R1guy]

3 hours ago, fatblokeonbandit said:

I have a cunning plan just need to find a 750 linkage

I guess they will rare 

Any good to you?

[fatblokeonbandit]

Oooooo that’s the kiddie
how much any thing you need for a swop

[clivegto]

750 swinging arm1100 swinging arm 

[fatblokeonbandit]

1 hour ago, clivegto said:

750 swinging arm1100 swinging arm 

Cheers Clive that confirms that i have 750 swinger  and linkage

[jb]

Just to confirm, it’s also the short 750 swing arm only fitted on the 750F first model (the G model onwards had a slightly increased wheelbase with a longer swing arm). Also if I remember correctly, it’s had the rear wheel adjusters bored slightly larger to accept the G model onwards rear wheel spindle     

[fatblokeonbandit]

11 hours ago, jb said:

Just to confirm, it’s also the short 750 swing arm only fitted on the 750F first model (the G model onwards had a slightly increased wheelbase with a longer swing arm). Also if I remember correctly, it’s had the rear wheel adjusters bored slightly larger to accept the G model onwards rear wheel spindle     

Cheers JB, that's good to know, I was wondering about the 20 mms spindle size

[fatblokeonbandit]

On 11/6/2021 at 6:30 PM, fatblokeonbandit said:

Excellent old skool chain tensioner, refurbished

 

I was thinking of getting a coloured wheel to replace the white plastic one, when I found these

 

Thye light up excellent!!!!!!!!!!!!!!!!!!!!!!!!!!

[fatblokeonbandit]

Going to need a clutch...

cabel clutch sprocket cover needed, 

 

I dug 4 out of the box.

 

 

But only one with the required leccy speedo pick up

 

 

offered it up and it wont go on, thought the push rod was too long, but on inspection the bugger is bent, and it wont pull out!!!!!!!!!!!!!

 

whipped the clutch centre out and got it out, this is what happens when you use an old piece of ordinary bar,, it bends and peens the end over.!!!

 

 

 

 

I got the engine off of a mate who had it fro a couple of years as a spare and never used it.

 

anywwya i have some spare push rods, just need to work out the length needed.

 

 

 

 

[fatblokeonbandit]

In the mean time i found a differant rear reservoir..

 

 

cant remember what from, but it fits a treat,, might use it or mabey just the green HRC tube??

 

 

 

[fatblokeonbandit]

Bolted the seat back on to see if all the leccy stuff fits underneath, southings a bit on the wonk somewhere!!!

 

[fatblokeonbandit]

Now with working cable clutch 

[Wagola]

15 hours ago, fatblokeonbandit said:

Now with working cable clutch 

Good to see you're using the anodised tat on this build ......

[fatblokeonbandit]

2 hours ago, Wagola said:

Good to see you're using the anodised tat on this build ......

I am indeed, in fact I might need to buy some long red/blue 6mm bolts!!!

[fatblokeonbandit]

Its now coming together a bit more..

 

 

 

 

 

[fatblokeonbandit]

Finished port side cooler bracket 

 

 

[fatblokeonbandit]

Spot the 2 deliberate mistakes

[Captain Chaos]

- reversed gearshift (up for 1st)

- oil lines on cam caps

Edited November 14, 2021 by Captain Chaos

[flatline]

On 6/20/2021 at 12:26 PM, fatblokeonbandit said:

Not sure how but the motor is 5 mm off to the Port side!??

 

better take all the spacers out and see what ive done wrong

 

Chain clearance??

[TonyGee]

can i give em a clue Garry ?

Edited November 14, 2021 by TonyGee

[flatline]

12 minutes ago, TonyGee said:

can i give em a clue Garry ?

Go on…. I haven’t read all of the thread… soo shot me down!! 

[fatblokeonbandit]

Yes the stupid `race pattern'  gear change, and I forgot to bolt the speedo rotor onto the end of the output xhaft, before the sprocket cover DOH!!!!!!!

[FJD]

Dont want to ruin your evening, but..

 

 

 

 

 

 

 

 

 

You forgot the chain too

[flatline]

7 minutes ago, FJD said:

Dont want to ruin your evening, but..

 

 

 

 

 

 

 

 

 

You forgot the chain too

Shaft-drive??