All Activity

Oh believe me I've been blipping it little and blipping it big without it helping. Going for neutral while it's in motion sometimes works

I only did the sync as it was quicker than the valves & it was cold in my garage.. all plugs are on vac ports - inlets are new & can't see any issues. Idle is a bit wooly up & down when it gets farty sometimes stops at nice rpm and then up a bit. I'm onto the valves next weekend.

Ideally valve clearances are checked and set before carb sync is undertaken. Assuming you have no vacuum leaks at the boots and as you are using a pingle tap, all vacuum take off ports on the carbs should be plugged off too. Assuming everything is ok internally with the carbs and your jetting is very very close if not bang on, then popping on decel is normal. Any popping/farting at idle Could be air leak related and or carb sync. Is the idle smooth or does it flactuate when popping then drop off then rise then settle etc?

Is the saunders fairing a bit like an Endurance one with one headlight. Not sen one of these frames before so build is going to be interesting to follow

It does it on over run which I'm quite happy with. But the idle erratic burbly farting (can't call it backfiring) & it's sometimes worse than other times, makes me think balance/valve clearance/ or leaks at exhaust to head? (Inlets are new). I've just noticed my victory in fitting the bsr carbs has shallowed a bit, as the middle synch screw is pretty inaccessible, but I now have vac take offs on both the carbs & the intakes. Think in going for the intake ones first. But rain is stopping here now, so set balance & it's a little better. Going to ride it before any more tinkering. But new valve cover gasket & exhaust gaskets on order for next weekends fun. Pick up response it much improved over dinosaur carbs!

What Gixer1460 said, plus "continuity" in this case is a small resistance, usually 3-5 ohms, which is enough not to be a dead short. With 12V it will draw 4 Amps and it's pulsed, so not on all the time.

The 'signal' wires ground out the coils to collapse the primary magnetic field and induce a mega voltage in the secondary whose only path to ground is through the spark plug.

you do get a certain amount of popping in an exhaust on carb'd bikes on the over run, but its masked by the standard exhaust so its hard to here, but on a free flowing exhaust its more noticeable.

In case you don't - a little blip of throttle whilst moving the gear lever, or moving the gear lever whilst still moving, will usually allow neutral selection. Basically either will 'unload' the clutch to allow easier movement - 101 big bike operation manual LOL!

Yes valve clearances are after a quick balance check/adjust today. I've not had exhaust off it - so I'm doubting the exhaust gaskets. It was a little poppy farty before I started all the mods, but ran fine once off idle. May well be valves, as I've done a lot of changes & it's flatulence is still there. Or it's just a characteistic of an old v&h empty 4 into 1?

Syncing the carbs might help your popping if they are still quite out after bench syncing. Might be worth checking valve clearances of you haven't already before syncing carbs. Do you mean the exhaust gaskets you haven't checked? Could cause popping if leaking a little.

So, I started with a set of mk1 1200 bandit carbs to fit. I then found a set of bsr36's from a 2002 750 tea pot - I don't know why but I chose these. Now all rebuilt with 20 pilots & 147 mains (never touched the little intermediate jet as 3 jets confuses me) needles on bottom groove / fuel screws at 3 turns. They went on with a bit more fuss - but OK, throttle cable a bit to short but original choke all bodged in. Running k&n pods on a v&h unbaffled with pingle tap. I've given the dyna s a full checking & given them a relay fed full 12v supply.... one day I must get rid of the cartridge fuse box. But now it's pissing down. I spent ages bench balancing the carbs & it starts + runs / revs quite nice in garage... but still has a poppy farty session in the exhaust at idle. I'm hoping a proper balance will smooth its flatulence? Also I've never removed the exhaust & checked head gaskets..... any advice on my lumpy farty poppy idle ( it's probably not as bad as I make it sound) but I'm hoping I can get it gone.

My super bodged timing wheel confirmed they are all good. I now have a new timing mark engraved for future use.

I've tried some searching here, and it got me wondering, is the gs750 clutch lever and perch I'm using not supplying enough leverage or travel for the gsx1100 engine? Could that be the issue? It was the same neutral problems with the cable adjusted to no slack at all, even with the clutch slipping if i where stopped I could not engange neutral easily. You can get pops and bangs from an overly rich tune as well, granted it's more of a burbly sound but still. It's hard to convey sound through writing

Popping through the pipe when you let off the throttle is lean. You need to go richer on the fuel screw and a bigger pilot if necessary.

Yep, I found them again

try and weeken the mixture screws off a quarter turn (in) and try it. and sounds like you have clutch drag !!!!!

Thanks for the advice, will check if there's a 12 V supply to the coils to the mentioned wire connection. Hoping this will be the case rather than cdi/signal generator issues. Will post back what I find. The one thing I don't understand is - if there is continuity when you resistance test the LT wires on the coil, how can it have a 12 V and electrical signal feeding at each end of the coil LT? I'm not an electrical expert!, just doesn't make sense to me. Thanks

So after getting my cams and timing in order I synced my carbs, adjusted ignition timing and set off, and it was immediately awesome! Right until I hit 5k rpm and the clutch started to slip. Luckily it was just a matter of adjusting the clutch cable. So off I went again and I'm blown away, this thing moves! However there's a few kinks that needs ironing out, namely: 1. Mixture seems to be to rich, it idles nicely but if you rev it it will settle at a couple of hundred maybe 300 rpms lower and then slowly work it self up to idling speed over the course of maybe 10seconds. I'm at 2 turns out on the mix screws, at what point do I consider moving to a size smaller pilot jet? 2. Lots of pops and bangs if I do a slight pull and then quickly let off the throttle in the low to midrange. I have a Hindle 4-2-2-1 exhaust so it doesn't dampen much but still, seems excessive, scared a dog and it's owner. Is this related to the rich idle mixture or more of a needle thing? Perhaps a combination? 3. Hard to get the thing into neutral, almost feels like the clutch is missing the last little bit to disengage enough. You have to force the shifter and because you force it it ends up usually jumping straight to second, or down to first depending on where you are. Any tips?

I use motul 300v mainly to stop cam wear.

There has been so much work and detail on this build.

Its looks ace.

On mine they were spot on