SiBag Posted September 11, 2017 Posted September 11, 2017 Are you running R1 Yokes ? If so I have a Harris R1 top yoke you may be interested in. Quote
fatblokeonbandit Posted September 12, 2017 Author Posted September 12, 2017 On 11/09/2017 at 0:14 PM, SiBag said: Are you running R1 Yokes ? If so I have a Harris R1 top yoke you may be interested in. I am going to use slingy yokes that have a stem for the F1 frame already in them, but if you need to find a home for the r1 yoke is it flat as I need to drill it for risers, and how much????? Quote
fatblokeonbandit Posted September 18, 2017 Author Posted September 18, 2017 Right removing powder coat.......I looked at the interweb and came up with this stuff, so strong the camera was blury, did it work like it says, no ..... it dose soften it but it dosent wipe off!!!! lost of scraping and its not bad.. i will perseveer.. Quote
Swirl Posted September 18, 2017 Posted September 18, 2017 I used powerstrip from that there auction site good results Quote
fatblokeonbandit Posted September 18, 2017 Author Posted September 18, 2017 Dichloromethane is the active ingrediant in that stuff, thats why i bought it as its 99% pure, perhapse the stripper would be better??? Quote
dupersunc Posted September 18, 2017 Posted September 18, 2017 Wurth Gasket remover works well on powdercoat. Quote
fatblokeonbandit Posted September 18, 2017 Author Posted September 18, 2017 I used loctitte gasket remover on a swinger 2 years ago, worked really well but was expensive, im trying to find cheaper alternatives, this dicholoromethane stuff is OK but evaporates quickly and stinks. Quote
MeanBean49 Posted September 18, 2017 Posted September 18, 2017 My mate owns a powder coaters, he always told me bit of fire is the best way to get it off, little gas lamp over it for a few seconds, comes peeling off Quote
Dezza Posted September 19, 2017 Posted September 19, 2017 As MB says above. Depending on what the powder coating is on, it can be removed by heat. If it's on steel and heat treatment is not going to bugger anything up, a great way to remove powder coating is to chuck whatever needs stripping on a bonfire. This worked brilliantly the last time I stripped some PC. When cooled down anything still on just drops off when brushed lightly with a wire brush. Quote
MeanBean49 Posted September 19, 2017 Posted September 19, 2017 Little gas blow torch is good for aluminium bits, its baked on at a really high temperature anyway when coated to start with. Quote
Swirl Posted September 19, 2017 Posted September 19, 2017 I was stripping a harris frame so I didn't want it blasting and didn't want it going in a bonfire, brushed powerstrip on it, left it to bubble and it peeled off with a stanley blade in a handle Quote
Dezza Posted September 19, 2017 Posted September 19, 2017 15 hours ago, fatblokeonbandit said: I used loctitte gasket remover on a swinger 2 years ago, worked really well but was expensive, im trying to find cheaper alternatives, this dicholoromethane stuff is OK but evaporates quickly and stinks. FB, have you tried adding some of the DCM to some paint stripper? The problem with paint stripper not working is because DCM has been removed. The consistency and other chemicals of the paint stripper, with DCM back in, should work in unison to work as paint stripper of old. Because paint stripper is a gloopy gel, you may not get the problem of the DCM evaporating quickly, especially if you cover the part covered in the paint stripper (with added DCM) with newspaper or cling film to reduce the effects of drying. An acetone/cellulose thinners mix kills paint but I haven't tried it on PC. You can fill a container with it, drop your part in, and then put a lid on it and leave it overnight. Maybe worth a try . This concoction really stinks but not if you use a Force 8 mask with chemical filters (not as expensive as you may think). I use mine all the time and wish I bought one years ago. 1 Quote
Dezza Posted September 19, 2017 Posted September 19, 2017 4 minutes ago, Swirl said: I was stripping a harris frame so I didn't want it blasting and didn't want it going in a bonfire, brushed powerstrip on it, left it to bubble and it peeled off with a stanley blade in a handle I agree, putting a bronzed welded/ braised frame on a bonfire is probably not a good idea. 1 Quote
fatblokeonbandit Posted September 19, 2017 Author Posted September 19, 2017 So the power strip stuff contains 0.1% DCM, the DCM I have is 99% pure!!!!!! so buy mixing it together I should make a really strong stripper, so what percentage ???? how much to add before I make something that will explode/poison me.... I will get some of it and some decent masks and have a go, we have a ventilated parts washer at work with a hood so ill do it there I think. just to be safe... Quote
fatblokeonbandit Posted September 19, 2017 Author Posted September 19, 2017 Cheers for all the good ideas chaps, ill report back if im still alive!!!!!!!!!!!!!!!!!!! Quote
Dezza Posted September 19, 2017 Posted September 19, 2017 9 hours ago, fatblokeonbandit said: So the power strip stuff contains 0.1% DCM, the DCM I have is 99% pure!!!!!! so buy mixing it together I should make a really strong stripper, so what percentage ???? how much to add before I make something that will explode/poison me.... I will get some of it and some decent masks and have a go, we have a ventilated parts washer at work with a hood so ill do it there I think. just to be safe... I would experiment with different concentrations of additional DCM. Take some of the 0.1% paint stripper and make some approximately 10 times more concentrated, so you have a gloopy gel of 1% concentration. It may not sound much but in the gel form it will stay in contact with the paint for much longer than the 99% stuff, as the 99% stuff is much more volatile and evaporates quickly. If that doesn't work you could try increasing the concentration. Quote
nlovien Posted September 20, 2017 Posted September 20, 2017 this is the exact stuff I used to strip a harris frame - I also used it to remove a twin pack epoxy fuel tank liner downside ? - there's no "sticky" viscosity to it so tried things like wrapping a cloth wetted with it, hands on keep working it with steel wool ( until yir fingers go numb with frostbite ) - made up a flour paste emulsion - they all worked to some degree - if you can immerse the part in this stuff - no problem, no paint or plastic, 2nd was the frostbite fingers and if it fails you can at-least destroy a few brain cells by sniffin it http://www.Eblag.co.uk/itm/Methylene-Chloride-Dichloromethane-99-5-10-Litre-10L-/302407462129?hash=item4668e3acf1 Quote
fatblokeonbandit Posted September 20, 2017 Author Posted September 20, 2017 1 hour ago, nlovien said: this is the exact stuff I used to strip a harris frame - I also used it to remove a twin pack epoxy fuel tank liner downside ? - there's no "sticky" viscosity to it so tried things like wrapping a cloth wetted with it, hands on keep working it with steel wool ( until yir fingers go numb with frostbite ) - made up a flour paste emulsion - they all worked to some degree - if you can immerse the part in this stuff - no problem, no paint or plastic, 2nd was the frostbite fingers and if it fails you can at-least destroy a few brain cells by sniffin it http://www.Eblag.co.uk/itm/Methylene-Chloride-Dichloromethane-99-5-10-Litre-10L-/302407462129?hash=item4668e3acf1 That's the stuff I have, im going to mix it with the power strip and see what happens Quote
Dezza Posted September 20, 2017 Posted September 20, 2017 It will probably be a good idea to be very careful working with concentrated DCM. This stuff will be absorbed directly through the skin and is used in cell biology as a solvent for flourescent dyes to stain some biological structures (this is when I have used this stuff), as it allows the dye to penetrate deep into the structure so it can be seen easily under a microscope. The vapour is probably not as bad as many other common organic solvents but latex gloves are required in labs when this is used. It should get your PC off though when you get the correct concentration in the DCM-free paint stripper. Quote
fatblokeonbandit Posted September 20, 2017 Author Posted September 20, 2017 I used gloves and goggles, as I read the SDS before hand, and did it out side, it did smell a bit though... Quote
Dezza Posted September 20, 2017 Posted September 20, 2017 Will be OK then, especially if using it outside. I will be very interested to know how much 99% DCM has to be added to what is now sold as 'paint stripper' in order for it to actiually remove paint. I have some so-called industrial stuff but it still doesn't work as well as Nitromors did 25years ago. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.