FJD Posted May 31, 2016 Share Posted May 31, 2016 Was offered a quite neat GS1000S that was submerged in 70cm deep water for probably 4 hours. After that, the engine was flushed with new oil. Seller told me the bike will need a total strip including engine teardown, as on some othe bikes he did not get the moisture out, and he already got surface rust inside engines. The flooding was probably 2 weeks ago. What about crank bearings/other roller bearings in the engine - changing required or not ? What do you think ? Quote Link to comment
bruteforce Posted May 31, 2016 Share Posted May 31, 2016 You won't know until you pull it apart. It'd only find it worth it if it is very cheap. Quote Link to comment
FJD Posted May 31, 2016 Author Share Posted May 31, 2016 all original for 2400 € Quote Link to comment
R1guy Posted May 31, 2016 Share Posted May 31, 2016 9 minutes ago, FJD said: all original for 2400 € Seems very expensive. Could buy a non flood damaged one for that.... Quote Link to comment
Captain Chaos Posted May 31, 2016 Share Posted May 31, 2016 salt water or not? If yes, don't walk away, but run. 1 Quote Link to comment
Gixer1460 Posted May 31, 2016 Share Posted May 31, 2016 70cm doesn't seem that deep - sort of nearly carb height? If so - there may be no water in it whatsoever? How else would it get in? Quote Link to comment
Captain Chaos Posted May 31, 2016 Share Posted May 31, 2016 just checked the EFE parked on the centerstand, 70cm is halfway the carb venturis. Quote Link to comment
Captain Chaos Posted May 31, 2016 Share Posted May 31, 2016 GS1000 would not be much higher/lower I guess. Quote Link to comment
johnr Posted May 31, 2016 Share Posted May 31, 2016 drop the oil first to see if any got in. but for a bike that may requaire an engine strip, new chain, new wheel bearings and a fair bit of remedial work, 2400 sounds like a lot of cash. was the previous owner not insured then? Quote Link to comment
FJD Posted June 1, 2016 Author Share Posted June 1, 2016 this guy is a quite high manager in car imports here, and a water pipe burst flooded his garage, lots of bikes were submerged, Kawasaki Z´s, CB750 KO, Vincent´s, Katanas, the GS1000S, BMW. What do good original GS1000S go for ? i followed an auction of an original left mirror - it went for $570.... Quote Link to comment
vizman Posted June 1, 2016 Share Posted June 1, 2016 4 hours ago, FJD said: this guy is a quite high manager ...so he didn't get wet? 7 Quote Link to comment
FJD Posted June 1, 2016 Author Share Posted June 1, 2016 i guess not ;-) i think he will get paid out good by the insurance, and now makes some extra $$ by selling off the unloved bikes Quote Link to comment
Swiss Toni Posted June 1, 2016 Share Posted June 1, 2016 (edited) As mentioned. Drain the oil, see what comes out. Better still, when drained, drop sump if owner will let you. Get a better look! Having said that, I bought a 750 Slabbie that had been left in the weather with plugs out, and carbs off. Inlets not plugged. I drained the oil and a bucket of water came out. Engine's fucked, I thought. On stripping it, bores were toast, bottom end was as new! So the one you're looking at may not be as bad as you think. Room for negotiation! Edited June 1, 2016 by Swiss Toni Quote Link to comment
johnr Posted June 1, 2016 Share Posted June 1, 2016 (edited) tbh if a bike is submerged its not a major problem if you strip it and sort it straight away. but if its been flooded and then sat round waiting for the insurance company to fork out then it could be ok, or it could be an utterly fucked rusty piece of crap and that should be reflected in the price. even if it were a minter pre flood, 2400 is a lot of cash for it cos its a huge gamble and by the time youve rebuilt it then you could have bought a runner and kept your hands clean. not for nothing to insuance firms write off submerged bikes as having zero value. however, tell him 2400 is fine, so long as he also accepts 2400 for the kat and 2400 for the vincent too.... Edited June 1, 2016 by johnr 1 Quote Link to comment
Reinhoud Posted June 3, 2016 Share Posted June 3, 2016 Replace the oil, and let it run for a long time! Then replace oil again Quote Link to comment
FJD Posted June 6, 2016 Author Share Posted June 6, 2016 bought it for straight 2 will make a new thread for it, when time permits 2 Quote Link to comment
teltwosheds Posted June 15, 2016 Share Posted June 15, 2016 Don't wast any time set it up (oil bores clean carbs drop old oil) and get it running quick! the engine heat will cook out any moisture Quote Link to comment
FJD Posted June 16, 2016 Author Share Posted June 16, 2016 all done, running like new ! 3 Quote Link to comment
Sheep Posted June 16, 2016 Share Posted June 16, 2016 Another one saved from the scrapyard in the sky... Quote Link to comment
FJD Posted June 21, 2016 Author Share Posted June 21, 2016 so here´s the beginning, that´s how i got it: washed down, plugs out, oil in cylinders, new oil in engine, engine turned over fine. no battery (was dead), not tried to start 1 Quote Link to comment
FJD Posted June 21, 2016 Author Share Posted June 21, 2016 the bike was covered in very thin protection oil, to prevent rust. the throttle was stuck in closed position - lucky me ! As soon as i got it on the bench, i took off exhausts, gas tank, carbs, side panels. Then removed starter, drained the oil, removed oil pan, generator cover, ignition cover, clutch cover There was still a little bit of water coming out from the engine cases, but inside everything was spot on, no rust to be seen - i came to rescue just in time ! Quote Link to comment
FJD Posted June 21, 2016 Author Share Posted June 21, 2016 The carbs were stuck - and that was probably my luck, as water only got in the combustion chambers 2+4 through the exhaust side. there was a bit of corrosion, that cleaned off with scotch brite. I cleaned the carbs thoroughly (not used my ultrasonic though - was too lazy), and got them moving properly again. Then checked cams - perfect, no water ! Then took out rear wheel - there was still water in between cushion dampener, also in the hollow parts of the hub, blew out with pressure air as good as possible. Also took out swinger and shocks, swingarm axle had light rust on it, regreased it good and fitted back to the bike. Quote Link to comment
FJD Posted June 21, 2016 Author Share Posted June 21, 2016 Then had to something about the chrome on the shocks, looked like that: ploished them up, then looked like this again: then gaskets came, and after repolishing clutch cover (had corrosion under clear laquer), this could be fitted again Quote Link to comment
FJD Posted June 21, 2016 Author Share Posted June 21, 2016 also polished the exhausts - i´m lucky, they are in pretty good shape, and solid too. Got it all together, and started her up - ran on all four as expected, gave her a good warm-up, smoked my whole shop with burning off the oil from inside the exhausts, and the corrosion protecting oil on the engine parts. Made a short test ride, everything works, only need a pair of mirrors (anyone got the correct ones ?) , they look like that: i ordered some GSXR 750 mirrors, they look similar, not sure if they fit. Also still need to get the airbox from prev. owner, so that i can really ride it normal (hustles a bit without airbox), and i need the two rear indicators and brackets. 2 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.