Harris magnum 2 but modern

[busa ash]

2 hours ago, markfoggy said:

I know where there's a breathed on (heavily I suspect, but no idea of the specs) GS1000 race engine. Needs a dash of lead in the fuel to stop it pinking, so something going on in there. Head has certainly been ported. It fell out of a successful club racing P&M,  surplus to requirements. Drop me a line if it sounds interesting.

sent you a message markfoggy

[markfoggy]

Replied, I've not mentioned this on here before 'cause the lump needs to go somewhere interesting. This seemed like a likely match 

[vizman]

ooh Cinderella it fits!

[busa ash]

an hour in the mancave and tadaah

[busa ash]

will be trying to get some of these from harris 

and under the red paint i find original decals 

 

chain run is looking good hopefully 

[busa ash]

and the parts are building up at work pending the garage electrics being done , and bidding on a couple of nice parts too

[Dezza]

Harris will send you the stickers free if you phone them. They ignore emails. At least they did a few years ago. If you find a good, cheap source of 531 stickers please post.

[busa ash]

dezza i bought an original 531 decal on eblag , £5 that was a one off ,

and then found some more but they where for pedal bikes as it says forks and tubes and stays 

[busa ash]

thats top shelf sorted , all new boxes sorted and refilled with stainless and my new waterproof wiring products .

12months of roof leaking till my best mate did new roof on garage 

now all i need too do is the middle shelf and move the b12 motor and gs 750 frame

 

[busa ash]

old harris foot plates and new gilies rear sets think i will be needing graph paper or a friend who does cad ?

 

still part sourcing as this was an impromtue build not long now till post man has a fit , have a colour scheme that might be a winner ( shhhh its a secret)

 

[busa ash]

got this it may go to hagon for a shorter end . but eblag bargain 

[SiBag]

23 hours ago, busa ash said:

old harris foot plates and new gilies rear sets think i will be needing graph paper or a friend who does cad ?

 

 

 

 

Is this a bit of a hint Ash,

Spose I do owe you for loan of the ramps n straps, and the rear brake pivot bush.

I'm off down in sunny south wales this week but will be back home at the weekend.

 

Si..

[busa ash]

what a smashing offer simon , no rush i want to get the seat height and wheels and forks in so its a one time measure  up 

[Rossco(Iceman Josros)]

On 25 April 2016 at 9:09 AM, busa ash said:

thats top shelf sorted , all new boxes sorted and refilled with stainless and my new waterproof wiring products .

12months of roof leaking till my best mate did new roof on garage 

now all i need too do is the middle shelf and move the b12 motor and gs 750 frame

 

Like the man cave Ash also just noticed the height of your neighbors fence 

[busa ash]

great neighbours  ginger ninja s house full ,,, 

collected some fancy 0 mile forks from an oss member monday and the yokes showed up tuesday like a plan only better 

[busa ash]

few more bits , clock bracket and headlight bracket in one 

 

as i had no caliper bolts for the radials , bit of bling and not too expensive 

[busa ash]

i am in the planning stage / mocking up deciding if i want  twin lights but modern or twin lights in fairing  

view from the front 

or not here but thinking of trying this too 

[busa ash]

On 19/04/2016 at 7:39 PM, Dezza said:

Harris will send you the stickers free if you phone them. They ignore emails. At least they did a few years ago. If you find a good, cheap source of 531 stickers please post.

 

many thanks too mark at harris for sending me 4 decals for my two restorations 

[busa ash]

A RIGHT BIG LUMP now out now it needs to be test fitted then painted black 

[Screwriverracing]

I can help with the 531 stickers

what would you like?

Cheers SRR

 

[busa ash]

2 hours ago, Screwriverracing said:

I can help with the 531 stickers

what would you like?

Cheers SRR

 

yes please i need 4 x 531 decals send me a message please 

[87flatside]

Very cool build / restoration never seen an early model here in the States I've only seen one here and that's a Harris magnum 5 which the guy did a real nice job with

 

 

Edited May 7, 2016 by Captain Chaos
it's a fucking 'onda

[busa ash]

 

and good news is my calipers have arrived in uk and should get them today or tommorrow

Edited May 9, 2016 by busa ash

[busa ash]

pictures are not showing admin ?

[Blubber]

Pics are showing.

 

tubes are in plus caliper bolts