fatblokeonbandit Posted April 7, 2022 Author Share Posted April 7, 2022 Not sure about plain steel look???? I think whites the way to go, whatever i choose will be later on after the summer.. Quote Link to comment
Wagola Posted April 7, 2022 Share Posted April 7, 2022 11 hours ago, fatblokeonbandit said: Not sure about plain steel look???? I think whites the way to go, whatever i choose will be later on after the summer.. I do like the the bare steel and brazed joints look with a clear coat to protect it. I'd do the same on my Mag 4 and still might on the next rebuild. Quote Link to comment
jejep4 Posted April 10, 2022 Share Posted April 10, 2022 But just varnished is not solid like real paint ? Quote Link to comment
fatblokeonbandit Posted April 11, 2022 Author Share Posted April 11, 2022 Whatever I do will have to wait. Castle coombe Classic track day next Friday week..!!! So better get me finger out, got it out and sorted all the small things and went for test flight number 2, much better, all that needs doing is the gear lever position sorting and the bastard clutch, its sooooo heavy, I think I must have fitted 2 HD springs instead of just one.... Anyway it went fine stopped brilliantly, carbs are not quite 100% but haven't got time to find a DYNO.. need to fit a baffle as its a bit loud Si instead I wiped it over with an oily rag, that will fix it 9 Quote Link to comment
fatblokeonbandit Posted April 22, 2022 Author Share Posted April 22, 2022 It was all going so well!!!!!!!!!!!!!!!! in an effort to make Brian pass the noise test at Casle Coombe, i fitted a differant race can, it worked well and its much more acceptable. BUT, the phone rang and when i came back i put the bike away without turning the Pingel off! couple of hours later Mrs fatbloke says " whats that smell" instantly I knew. ran out to gargae and about 20 quids worth of super duper unleaded is on the gargae floor.. Bollox, so carbs off and clean them out again to seal the float valves and empty the engine of gas.. Bloody motor bikes 5 Quote Link to comment
davecara Posted April 22, 2022 Share Posted April 22, 2022 35 minutes ago, fatblokeonbandit said: BUT, the phone rang and when i came back i put the bike away without turning the Pingel off! couple of hours later Mrs fatbloke says " whats that smell" instantly I knew. ran out to gargae and about 20 quids worth of super duper unleaded is on the gargae floor.. Bollox, so carbs off and clean them out again to seal the float valves and empty the engine of gas.. Bloody motor bikes Thats only about a teaspoon full these days! Full trackday report back please 1 Quote Link to comment
fatblokeonbandit Posted April 22, 2022 Author Share Posted April 22, 2022 1 hour ago, davecara said: Thats only about a teaspoon full these days! Full trackday report back please Might be on the teapot yet.... in fact im taking both just incase.. need to find my on board camera and make bracket as awell.. 1 Quote Link to comment
TonyGee Posted April 22, 2022 Share Posted April 22, 2022 these things are sent to try us but we still love em Quote Link to comment
fatblokeonbandit Posted April 22, 2022 Author Share Posted April 22, 2022 Carbs off, 2 vlaves had bits of shite in them keeping them open... Next have the tap apart and check the strainer i suppose??? Quote Link to comment
Wagola Posted April 22, 2022 Share Posted April 22, 2022 28 minutes ago, fatblokeonbandit said: Carbs off, 2 vlaves had bits of shite in them keeping them open... Next have the tap apart and check the strainer i suppose??? Stick an inline fuel filter on it ? Quote Link to comment
Gixer1460 Posted April 22, 2022 Share Posted April 22, 2022 This will piss you off then - Just sold SWMBO's trike this morning, hasn't run in at least 5 years, turned on tap (with whatever fuel was in there), pulled choke and it was on jump leads but fired up after about a minute of cranking & some EasyStart and sat ticking over, smooth idle after 30 seconds . . . . . . . . amazed me, stunned the buyer - life can be like that I guess LOL! I guess you are lucky that fuel stayed external and you didn't fill the crankcases ? Quote Link to comment
TonyGee Posted April 22, 2022 Share Posted April 22, 2022 27 minutes ago, Gixer1460 said: I guess you are lucky that fuel stayed external and you didn't fill the crankcases it did Quote Link to comment
fatblokeonbandit Posted April 22, 2022 Author Share Posted April 22, 2022 Yes oils a bit smelly I’ll change it anyway,, and took the tap out bugger me no filter that will do it 1 Quote Link to comment
Dezza Posted April 22, 2022 Share Posted April 22, 2022 Have you dismantled the tap or have you just removed it from the tank? If just taken from tank then it looks like the tap has been modified as there should be a bit sticking out of the hole in the middle, and also a ridge where the filter gauze is pressed into. Quote Link to comment
fatblokeonbandit Posted April 22, 2022 Author Share Posted April 22, 2022 Yes been modified so I found some filter gauze and made a filter, that will do for now in case I can’t get a new one??? 2 Quote Link to comment
Gixer1460 Posted April 22, 2022 Share Posted April 22, 2022 4 hours ago, TonyGee said: it did Bugger! Quote Link to comment
fatblokeonbandit Posted April 22, 2022 Author Share Posted April 22, 2022 3 minutes ago, Gixer1460 said: Bugger! Bugger indeed the oil is newish so it will need dumping Quote Link to comment
fatblokeonbandit Posted April 22, 2022 Author Share Posted April 22, 2022 1 hour ago, Dezza said: Have you dismantled the tap or have you just removed it from the tank? If just taken from tank then it looks like the tap has been modified as there should be a bit sticking out of the hole in the middle, and also a ridge where the filter gauze is pressed into. It didn’t leak, shipmate, some dipstick left it on 1 hour ago, Dezza said: Quote Link to comment
fatblokeonbandit Posted April 22, 2022 Author Share Posted April 22, 2022 (edited) Anyway fitt3d clean carbs, new plugs and oil and fired it up, much better noise wise. so whipped the clutch springs out???? thers 3 in there 2 Barnett HD and a standard one?? had a think and realised I just had a look and saw the H/D spring and left it, looks like someone in the past was too tight to fix a slipping* clutch better have it to bits and have a look!!!! Fekin motorbikes!!!!!! Edited April 22, 2022 by fatblokeonbandit 1 Quote Link to comment
fatblokeonbandit Posted April 23, 2022 Author Share Posted April 23, 2022 FEKIN motorbikes!!!!!!!!!!!!!!!!!!!!!!!!! This engine came from a mate who had it sat in garage for 3 years he bought a running b12 and took the motor out, He rode it home so I assumed the engine was good, .. Not only was there 3 diaphragm springs in the 2 x HD and a std one, but one too many steel plate and lots of fecked fibers!!!!!!!!!!!!! The hubs been baked as well. ARSE bugger and BUM 5 days to first track day..... better go find all the missing bits I suppose, Quote Link to comment
Dezza Posted April 23, 2022 Share Posted April 23, 2022 Look at the positives: it's good you found that lot now rather than after some of that clutch debris blocked an oilway halfway through a track session and buggered up something very expensive Quote Link to comment
clivegto Posted April 23, 2022 Share Posted April 23, 2022 Wow never seen plates like that before or the drum turned blue. Quote Link to comment
fatblokeonbandit Posted April 23, 2022 Author Share Posted April 23, 2022 36 minutes ago, Dezza said: Look at the positives: it's good you found that lot now rather than after some of that clutch debris blocked an oilway halfway through a track session and buggered up something very expensive Wise words matey, wise words….. yup much better finding it now than next Friday at castle Combe. Just hope I can sort all the issues, I have teapot and b12 running ok now so have back up…….. 1 Quote Link to comment
fatblokeonbandit Posted April 23, 2022 Author Share Posted April 23, 2022 10 minutes ago, clivegto said: Wow never seen plates like that before or the drum turned blue. I have had one with plates fell to bits, they were non Suzuki ones and some idiot wheeled it everywhere then complained the clutch went Not seen a hub that hot though I reckon some idiot had this one and the clutch slipped so added HD springs, it still slipped so stuck another spring then another steel to attempt to stop slippage…. 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.