Swirl Posted June 28, 2018 Posted June 28, 2018 1 hour ago, busa ash said: paul was already done but can take pictures for you mate Cool, I'll look forward to them, I've seen how Davecara's is done so looking for my best option Quote
busa ash Posted June 29, 2018 Author Posted June 29, 2018 Dave s is done better than mine I am sure mate Quote
busa ash Posted June 29, 2018 Author Posted June 29, 2018 Bit of time trying out clock position . Before I start modifying and making some mounting brackets 4 Quote
vizman Posted June 29, 2018 Posted June 29, 2018 do you still have the cut-down riders seat Ash? Quote
busa ash Posted July 4, 2018 Author Posted July 4, 2018 On 6/29/2018 at 8:45 PM, vizman said: do you still have the cut-down riders seat Ash? no when i bought the bike i swapped to the full height one viz Quote
busa ash Posted July 15, 2018 Author Posted July 15, 2018 Did a bit of fettling on exhaust system too get it looking better 3 Quote
busa ash Posted July 15, 2018 Author Posted July 15, 2018 Next just been and collected a 5.5 inch x 17 in rear wheel too match up with new front , also looking at fitting a 6 pot rear radial calipers if I can . 5 Quote
Madb Posted July 15, 2018 Posted July 15, 2018 are you leaving that wet tyre on? love that six pot! Quote
busa ash Posted July 15, 2018 Author Posted July 15, 2018 2 minutes ago, Madb said: are you leaving that wet tyre on? love that six pot! No not leaving wet on it's just how I bought it 1 Quote
KATANAMANGLER Posted July 15, 2018 Posted July 15, 2018 30 minutes ago, Swirl said: Katana mangler was after a wet matey Cheers @Swirl I got sorted with wets. 1 Quote
busa ash Posted July 21, 2018 Author Posted July 21, 2018 have now got some billet drag slots and the sprocket carrier has shown up Quote
clivegto Posted July 23, 2018 Posted July 23, 2018 Nice, they look a lot like my latest ones Ash can not guess why lol. 1 Quote
vizman Posted July 23, 2018 Posted July 23, 2018 nice, new paint makes a whole load of difference 1 Quote
Ådne95 Posted September 13, 2018 Posted September 13, 2018 Gotta love a efe How easy does the K3 1000 front end fit? Can you use the triples off that? Quote
SiBag Posted September 16, 2018 Posted September 16, 2018 On 9/13/2018 at 10:10 PM, Ådne95 said: Gotta love a efe How easy does the K3 1000 front end fit? Can you use the triples off that? They go in easily. Just a top bearing swap forks are a tad short so a at stepdown yoke is a good idea. 1 Quote
Ådne95 Posted September 17, 2018 Posted September 17, 2018 On 9/16/2018 at 7:43 PM, SiBag said: They go in easily. Just a top bearing swap forks are a tad short so a at stepdown yoke is a good idea. *pic* Thanks! I see Well - any ecxuse to do some machining is just great Quote
Gsxrsam Posted September 18, 2018 Posted September 18, 2018 On 7/23/2018 at 8:02 PM, clivegto said: Nice, they look a lot like my latest ones Ash can not guess why lol. There are more parts for you, if you are passing.......:) 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.