clivegto Posted December 1, 2017 Posted December 1, 2017 (edited) Stumbled upon these harris k8 adjustable yokes & finally got my hands on them today. Haven' got time to play with them at the moment as its Mrs gto's birthday. Edited December 1, 2017 by clivegto 8 Quote
SiBag Posted December 1, 2017 Posted December 1, 2017 You lucky barsteward.... That's a epic set of yokes. 2 Quote
clivegto Posted December 3, 2017 Posted December 3, 2017 Corbin seat will need butchering a bit at the front. 2 Quote
clivegto Posted December 5, 2017 Posted December 5, 2017 Had a think about fitting the seat & if I move it back a little bit it fits the tank fairly good. Chopped the original seat fastening lugs of the sub frame. Also cut some material from the seat unit to let the seat go further back. I then made a cross piece with notches in, to replace the sub frame lugs. Drilled some 6mm holes in it to fasten it to the sub frame. Stuck some neporin to the front of the seat to fill the small gaps. Srill need to make some thing to fasten the seat at the front but am pleased with it for now. 2 Quote
clivegto Posted January 18, 2018 Posted January 18, 2018 Gsxrsam has made the drag slots there lovely he still needs to finish the adjuster blocks but hopfuly it will be done tomorrow, the blocks inbetween are to hold it square while been welded. Just need Will to weld them on now. 8 Quote
clivegto Posted January 31, 2018 Posted January 31, 2018 Now have 2 yoshimura replica oil catch tanks one for the Harris & one for the NWS slabby . 7 Quote
SiBag Posted February 1, 2018 Posted February 1, 2018 I like the catch tank. Looks the part with the Harris frame 2 Quote
clivegto Posted February 5, 2018 Posted February 5, 2018 (edited) Got the drag slots welded on . Brace is just sat on loosely for mock up picture of what it might look like. Edited February 5, 2018 by clivegto 2 Quote
clivegto Posted February 14, 2018 Posted February 14, 2018 @Gsxrsamhas made me some very nice adaptor plates for the Harris rear sets. Need to sort out the gear linkage with the oil tank been there as the linkage sticks out a little further. Also need to fit the Harris back master cylinder. 7 Quote
Swiss Toni Posted February 21, 2018 Posted February 21, 2018 Just re-read the whole build. Great work, Clive. You've put me to shame! 1 Quote
clivegto Posted February 21, 2018 Posted February 21, 2018 1 hour ago, Swiss Toni said: Just re-read the whole build. Great work, Clive. Thank you, it's going a little slower at the moment. Quote
clivegto Posted February 22, 2018 Posted February 22, 2018 (edited) Didn' have a stem for the Harris yokes no standard ones I have come across would have fitted. Rather than make a lot of work for Sam thought I would ring Harris Performance. Phoned them spoke to Mark & Nigel both very helpful they had them on the shelf. Got it today, stem for harris super bike adjustable yokes. Looks to me with this stem you could fit these to just about any big bike. Just need to sort some bearings out to fit them now. Edited February 22, 2018 by clivegto 4 Quote
Gsxrsam Posted February 22, 2018 Posted February 22, 2018 What are diameters of bearings needed? 1 Quote
Dezza Posted February 22, 2018 Posted February 22, 2018 The stem, with the long threaded part and threaded bit for the top bearing, looks like a great idea to copy for other yokes because it can obviously be adjusted to enable the yokes to fit a variety of different headstock lengths 2 Quote
clivegto Posted February 22, 2018 Posted February 22, 2018 1 hour ago, Gsxrsam said: What are diameters of bearings needed? Will let you know. 26 minutes ago, Dezza said: The stem, with the long threaded part and threaded bit for the top bearing, looks like a great idea to copy for other yokes because it can obviously be adjusted to enable the yokes to fit a variety of different headstock lengths Yes. Quote
clivegto Posted February 23, 2018 Posted February 23, 2018 15 hours ago, Gsxrsam said: What are diameters of bearings needed? There 26x52x16mm & 30x52x16mm top one is only 1mm different mate. Quote
Gsxrsam Posted February 23, 2018 Posted February 23, 2018 Expensive for decent sealed ones.....https://simplybearings.co.uk/shop/p43730/4TCR0643L/0643-NTN-Narrow-Section-Steering-Head-Set-Taper-Roller-Bearing-30x52x16mm-SEALED-MODEL/product_info.html https://simplybearings.co.uk/shop/p43727/265215-Narrow-Section-Steering-Head-Set-Taper-Roller-Bearing-26x52x15mm/product_info.html 15mm for the top one..... Quote
clivegto Posted February 23, 2018 Posted February 23, 2018 Cheers @GsxrsamBottom one is same as b12 etc its the top one thats a bit different, could not find one but you have 1 Quote
clivegto Posted March 3, 2018 Posted March 3, 2018 Got some bearings for the stem & a number plate holder from China like the one @370stevealso got. £19.99 delivered unbelievably how they can do it for that. 3 Quote
370steve Posted March 3, 2018 Posted March 3, 2018 christ they are expensive now !!!!!!!! i only paid £12.34 delivered from the same guy 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.