Harris magnum 2 but modern

[busa ash]

Few updated pictures 

 

Swapped tank with clive as he needed a standard mag 2 for his up coming build 

Edited September 11, 2019 by busa ash
Missing words

[busa ash]

[busa ash]

[busa ash]

[busa ash]

Lots of little bits done or re done 

Loom done and looking at a little clutch pull mod at the moment 

Last two pictures .

Few bits going for powdercoat for my other harris so will chuck the clutch cable bracket in with the other bits 

[clivegto]

Looks good Ash. 

[busa ash]

Thanks clive 

[SiBag]

Nice Tank, surprised it works so well with the old style seat unit.

[busa ash]

2 hours ago, SiBag said:

Nice Tank, surprised it works so well with the old style seat unit.

Totally agree mate I was gobsmacked 

[busa ash]

Bit more done decal needed so ordered , glad I have persevered with this headlight set up now 

[busa ash]

Also got keys cut to lock so I can use Harris filler cap 

[busa ash]

Ordered some more stripe this is an off cut too see if I get the desired effect 

[busa ash]

Exhaust time , have sent emails to two companies for a stainless swaged 2.5 to 3.5 inch pipe

[busa ash]

Few more steps forward and then brand new chain too short ...

Made indicator mounts and Re fitted stripe so it fits headlight better  long list of parts still to fettle it's the last 10% of a build that takes the longest 

[Swiss Toni]

Looks very nice, Ash!

[Swirl]

On 10/3/2019 at 4:36 PM, busa ash said:

Exhaust time , have sent emails to two companies for a stainless swaged 2.5 to 3.5 inch pipe

Did you get sorted, a mate of mine does exhaust if your not sorted 

[busa ash]

1 hour ago, Swiss Toni said:

Looks very nice, Ash!

Thanks mate time and money both scarce, but put effort in when I can in my little cave

[busa ash]

Exhaust Tom Foolery 

[busa ash]

1 hour ago, Swirl said:

Did you get sorted, a mate of mine does exhaust if your not sorted 

Yes mate sorted 

[baldrick]

its looking good now, but the exhaust im not so sure about, personally. it looks un balanced, if you get my drift, maybe its the masking tape, I dunno ?

could racefit not have knocked you up a connector from the can to mimic the rear of the can, i.e. hidden under the carbon, and rivitted?. and with springs instead of that ugly connector bracket?

 

anyway its not my bike so just ignore me.  I couldn't agree more about the last 5-10% being the most difficult to complete the build, its always the way eh? 

Whats next to be done?

Edited October 16, 2019 by baldrick

[busa ash]

Racefit could have I am sure but I dont have race fit money , I own a few bikes so money is thin on the ground . Race fit only use titanium and I have stainless headers and link pipe , I am only using the racefit can as it's all I have in 2.5 inch on the shelf .

Need an offset 525 sprocket the hunt continues 

[clivegto]

3 hours ago, busa ash said:

 

Need an offset 525 sprocket the hunt continues 

Some kawasaki front sprockets were offset may have been gpz750, can't remember what size though. 

[370steve]

4 hours ago, busa ash said:

Need an offset 525 sprocket the hunt continues 

Ask Chas at B&C Express, he will know what you need

[busa ash]

I spent an hour with a flap disc I now have a modded sprocket was 530 now 525, tried grumpy 1260 and talon no joy in 525 

[vizman]

I couldn’t find an offset 525 front sprocket anywhere for the dudettes slabby, so I made one out of two, didn’t even cross my mind to whittle down a 530 one....