Svsam Posted December 12, 2022 Share Posted December 12, 2022 Does anyone know if they differ j/k to l/m I have these l/m forks which were on a blandit, decided they are going towards a ‘make a bike from spares’ project, found a gsxr stem..or so I thought to swap out the bandit one, went to work to use the press to swap em, gets home to fit and there isn’t enough length to get the top nut on. j/k frame, are they deeper headstock that the later l/m? Quote Link to comment
clivegto Posted December 13, 2022 Share Posted December 13, 2022 I thought all the gsxr stems were the same length same length as the air cooled ones as well bud. 1 Quote Link to comment
TonyGee Posted December 13, 2022 Share Posted December 13, 2022 2 hours ago, clivegto said: I thought all the gsxr stems were the same length same length as the air cooled ones as well bud. me too 1 Quote Link to comment
Captain Chaos Posted December 13, 2022 Share Posted December 13, 2022 me three 1 Quote Link to comment
Svsam Posted December 13, 2022 Author Share Posted December 13, 2022 Maybe it’s not a slingy one then Quote Link to comment
Rossco(Iceman Josros) Posted December 13, 2022 Share Posted December 13, 2022 Me four so could it be from an R1 as iircc these are shorter than gsxr’s but i maybe wrong 1 Quote Link to comment
Paulm Posted December 13, 2022 Share Posted December 13, 2022 All the same as far as I'm aware. 1 Quote Link to comment
Devilman Posted December 13, 2022 Share Posted December 13, 2022 (edited) As far as I am aware all the stems should be the same across the GSXR's. Is it possible you either haven't pressed the stem in far enough, or do you have any "Custom Yokes" that may be thicker? Bit of a cheeky blag here but I'll give it a punt anyway.... I am in need of a Bandit stem and I have the front-end from a 750J sat here in my garage ... Perhaps you would be interested in a trade? (Your Bandit Stem for my 750J Stem) Edited December 13, 2022 by Devilman 1 Quote Link to comment
Svsam Posted December 14, 2022 Author Share Posted December 14, 2022 8 hours ago, Devilman said: As far as I am aware all the stems should be the same across the GSXR's. Is it possible you either haven't pressed the stem in far enough, or do you have any "Custom Yokes" that may be thicker? Bit of a cheeky blag here but I'll give it a punt anyway.... I am in need of a Bandit stem and I have the front-end from a 750J sat here in my garage ... Perhaps you would be interested in a trade? (Your Bandit Stem for my 750J Stem) I’ll drop you a message after with a pic of the bandit stem. I’d call it functional, but it does look like 2 welded together would be interested in trade though yes Quote Link to comment
Gsxrsam Posted December 16, 2022 Share Posted December 16, 2022 check against this..... 3 Quote Link to comment
Svsam Posted December 28, 2022 Author Share Posted December 28, 2022 So I’ve done a lot of sitting and researching and drinking..and then staring again the next evening. I think the 750l/m is an anomaly. the lock stops are in a different place on the bottom yoke, the are at the back side of the yoke opposed to all others I find are at the front or a single one at the front. (I cut them off mine) So maybe the stem is slightly different too. I measured the bottom of the stem that came out and it’s 30.5mm (larger than 30.25 @Gsxrsamkindly posted above) I have exactly the same forks on the turbo slingy which is also a j/k frame. Anyone got a 750 L/M stem they could measure, lend or sell? pic of my extensive research.. Quote Link to comment
davecara Posted December 28, 2022 Share Posted December 28, 2022 I've got a set of yokes you couldve taken ya wally Quote Link to comment
Svsam Posted December 29, 2022 Author Share Posted December 29, 2022 7 hours ago, davecara said: I've got a set of yokes you couldve taken ya wally Fack n’ ell! 1 Quote Link to comment
clivegto Posted December 29, 2022 Share Posted December 29, 2022 Just remembered I have your old front end hear. Stem length looks to be 257 258mm & just over 30mm at the bottom. 1 Quote Link to comment
Captain Chaos Posted December 29, 2022 Share Posted December 29, 2022 16 hours ago, Svsam said: I think the 750l/m is an anomaly. the lock stops are in a different place on the bottom yoke, the are at the back side of the yoke not on both my 750L front ends. Quote Link to comment
Svsam Posted December 29, 2022 Author Share Posted December 29, 2022 1 hour ago, Captain Chaos said: not on both my 750L front ends. Oh dang it. Thought I was onto summit! @clivegtothe stem on this is much longer about 273mm but it has had an extension piece welded in the middle. and it’s definitely a good 30.5 diameter at the bottom where I hadn’t pressed it in all the way that .4 of a millimetre is enough for the (gsxr) stem to drop out. and still baffled why it wasn’t long enough at 256mm. Quote Link to comment
Gsxrsam Posted December 29, 2022 Share Posted December 29, 2022 7 hours ago, clivegto said: Just remembered I have your old front end hear. Stem length looks to be 257 258mm & just over 30mm at the bottom. 30mm is bearing size...press in bit is 30.3 on slingy. 1 Quote Link to comment
Gsxrsam Posted December 29, 2022 Share Posted December 29, 2022 5 hours ago, Svsam said: Oh dang it. Thought I was onto summit! @clivegtothe stem on this is much longer about 273mm but it has had an extension piece welded in the middle. and it’s definitely a good 30.5 diameter at the bottom where I hadn’t pressed it in all the way that .4 of a millimetre is enough for the (gsxr) stem to drop out. and still baffled why it wasn’t long enough at 256mm. sounds like you have bandit stem... 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.