Jump to content

rodneya

Members
  • Posts

    92
  • Joined

  • Last visited

Everything posted by rodneya

  1. Mark Walker making sweet looking frames for oilcooled GSXR.
  2. In the UK maybe, but in Canada there are not that many that I have seen for sale. Water cooled motors are a different story.
  3. Well EFE it is then. thanks.
  4. Got an opportunity to buy a new motor and have two options. EFE motor with 1200 kit and cams ( cant remember what the guy mentioned at the moment) or a 1127 oil cooled motor from a late 80's say what now!? and looking for some opinions. Motor may go into my Katana, or a future project. And yes I would like both, but I dont think I can swing that at the moment.
  5. Pics are pretty small, so hard to see, but is that mat finish?
  6. was that frame originally brazed together?
  7. 1127 motor from a 1991 Katana 1100. Is this motor the same as the older gsxr 1127 motors? I cant seem to find any useful info anywhere.
  8. Motogpwerks sells these billet brackets to fit a small Brembo under slung to a SRAD without a torque arm. Shouldn't be to hard to get one made to fit.
  9. If there is a lot of rust or old fuel residue it will speed the process up if you remove some of it first. I put a handful of drywall screws in the tank and sloshed it around with some water. They did a great job scraping off the big stuff and are easy to get out with a little magnet on a telescoping rod or something.
  10. It was sawzolled just behind the motor. Meant to look like a badly crashed bike. They even cut the back of the tank. I cleaned up to motor and sold it. Had a bunch of gouges out of the back of the cases and a cut into the clutch cover.
  11. I bought a movie prop SRAD to use as parts. It was cut in half and had been painted really badly with rattle cans. I managed to get just the spraypaint off stuff with thinners or acetone on a rag. the factory paint is a lot harder to remove.
  12. If you use something like concrete remover that is quiet aggressive you will need to line the tank to stop flash rusting. I used electrolysis for my tank and the last few rounds I used TSP solution. This leaves a phosphate coating that does not flash rust.
  13. Ive always had good results with deck screws. Hammer the tip in a bit first
  14. That looks to be exactly where it goes. Thank you very much Arttu. I asked this on a few different places and got absolutely zero answers back. Gotta love the previous owner of this bike. I guess the huge amount of blue silicone gasket maker that was smeared all over the motor and inlets and the speaker wire in the harness should have been a giveaway to his ability to do a decent job of anything.
  15. Nope, No 8 is a huge thick washer with a groove across the one side
  16. My 1982 750 Katana has a 1983 GS1100E motor. Putting the clutch basket back in I noticed that there were two washers behind the oil pump drive gear when I took it apart. Parts diag shows only 1 washer that is 25mm by 50mm by 2.5mm thick. With this in place the gear lines up with the gear on the oil pump. The other one I have is 25mm by48mm by 1mm thick. Any Ideas where this should go?
  17. rodneya

    Rusty tank

    I use electrolysis on my Katana tank. The last few rounds I used TSP solution. It leaves a phosphate coating that prevents flash rusting after rinsing out the tank. Its pretty slow, but it worked perfectly. I will not damage paint either.
  18. where about are you located? You can buy mine.
  19. Why do you say to always use the headlight? Is it because one of the stator power wires goes directly to the headlight?
  20. There is no spot for a temp gauge on this, just the pressure sender. The hole on top is for the rear mounting bolt.
  21. These adapters are advertised as fitting the GS 2 valve motors. Is there a reason that it can not be used on a 4 valve motor as long as it clears the tensioner wheel?
  22. I just looked at the sheet that came with my JE 1270 Kat pistons, and the recommended clearance is 0.0508mm or 0.0020 inch. That is for a 75mm bore. Your clearance is 3 times more on a 78mm bore
  23. Can you add a bulb inside the case to fool the sensor into thinking its daytime?
  24. That looks like a lot of work. You would have to make a mould of the tank and use vacuum bags and all the special layers that go with it to get a tank without pinholes. And it will still need a liner to stop the crappy stuff in the fuel from eating the inside.
×
×
  • Create New...