-
Posts
1,281 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Everything posted by Madb
-
Me just turned green! Thier shall be many looking at the show . Yum yum.Awesome
-
1994 GSXR 750 WR Petcock
Madb replied to skunkrider2's topic in Water Cooled, V-Twins, Singles and 2-strokes
You will need to undo the screws that hold the shaft in . Then push it though. If i remember correctly. But i may have remembered.Wrongly. It has been known.(to often receintly) -
Bandit 400, bane of my existence
Madb replied to Scareraven's topic in Water Cooled, V-Twins, Singles and 2-strokes
About 150-200 pounds should get ya one big enough. On Eblag. Make sure they're 40hz tho. You can get proper carb solution off net. @Yoshijohnny is the man to ask on here. -
W exhaust port spacing
Madb replied to Captain Chaos's topic in Water Cooled, V-Twins, Singles and 2-strokes
I know, late to the party, again. Anyway, Did you get them to fit? -
W exhaust port spacing
Madb replied to Captain Chaos's topic in Water Cooled, V-Twins, Singles and 2-strokes
1-2 is 85mm 2-3 is 121mm approx . Hope that helps -
Nice video. Love the music. Tho i were expecting Vizman & co to start a rappin chant.
-
1100 wp Fork Oil
Madb replied to NorthernBloke's topic in Water Cooled, V-Twins, Singles and 2-strokes
+1 ^^^ -
2000 gsxr600 rotor bolts
Madb replied to laxcdn's topic in Water Cooled, V-Twins, Singles and 2-strokes
should have gone to spec savers. -
1100WP definative noisy alternator fix?
Madb replied to NorthernBloke's topic in Water Cooled, V-Twins, Singles and 2-strokes
the w/c motors from 92-98 models will fit. rf900,750,600 and of coarse the 1100 w/c. (tho they may be rated for different amps)the older oil cooled ones won't fit. but the altenators are noisey on these models. as wombat say's just check the rubbers and play on the shaft. if that checks out ok there maybe some play on the bearing under the cover where the alt goes in. link below for referance. https://www.ronayers.com/oemparts/l/suz/50d3ce02f870021958f28413/1993-gsx-r1100w-parts -
i bet ya feel all 17 years old again,eh! lush. weather looking good for a bit too.. happy days.
-
Mablethorpe contender
Madb replied to fastgs287's topic in Water Cooled, V-Twins, Singles and 2-strokes
Anything! if it's on the beach!!!! -
Looks like it's just rolled out of the showroom. Good job!
-
How about water-cooled V4s?
Madb replied to Madman85's topic in Water Cooled, V-Twins, Singles and 2-strokes
i know their are not many running. be nice to hear one again! -
How about water-cooled V4s?
Madb replied to Madman85's topic in Water Cooled, V-Twins, Singles and 2-strokes
does anyone own a RE5? -
We can see your grin getting bigger... Not long now for ringadinga..ding.ding
-
What paint will one be using for them calipairs?
-
These are from an SV650, but the lever and foot rest is off a set of Gilles. Dan moto appears to have copied Gilles design tho not the Quality! you can see my adaptor plate. when i can afford it i shall be replacing these rearsets tho.
-
I haven't found any one that makes them. Not now anyways. you could check sites in japan for yoshi and the like. I made a plate up so i could bolt on newer K series sets, sv ones are the same as k ,tho some of the newer ones have the gear link mounted to the frame. Just make some adaptor plates and fit the ones ya fancy.
-
bet they're based on rf900's!
-
need to onder one for my water bucket when funds allow. think it were mark up at £80.00 quid. may be more now as i havent looked for a while. how do they make them for that? don't care, better for us i guess.
-
some nice rads on Eblag from china for not much dosh. they seem to be of good quality too. less than 100 notes too!
-
depends where you are but @gsxr884 is the man to goto on here. but as ya only have 4 posts ya might not see him the traders section.