yantosh Posted January 18, 2020 Author Share Posted January 18, 2020 back to the 19 canteen mill, drill the clamp holes 4 Quote Link to comment
clivegto Posted January 20, 2020 Share Posted January 20, 2020 Very smart indeed. 1 Quote Link to comment
yantosh Posted January 21, 2020 Author Share Posted January 21, 2020 clamp slots cut, no chance to put final detail on risers yet. wheel spindle next 3 Quote Link to comment
SiBag Posted January 22, 2020 Share Posted January 22, 2020 The logo on the bottom yoke works well.. 1 Quote Link to comment
busa ash Posted January 22, 2020 Share Posted January 22, 2020 yan your work has always been top notch , loving this build . the logo is top draw 2 Quote Link to comment
yantosh Posted January 22, 2020 Author Share Posted January 22, 2020 risers machined and on 6 Quote Link to comment
yantosh Posted January 24, 2020 Author Share Posted January 24, 2020 flung the galfer discs on, better than them lying about getting in the way Quote Link to comment
yantosh Posted February 14, 2020 Author Share Posted February 14, 2020 got the frame off the jig, couple of bits to do the prime to protect it from the dreaded orange rash The two rear tubes are getting replaced, they foul the swingarm 2 Quote Link to comment
yantosh Posted March 4, 2020 Author Share Posted March 4, 2020 started the stem nuts, friend started my footpegs 2 Quote Link to comment
yantosh Posted March 4, 2020 Author Share Posted March 4, 2020 front mocked up in frame 4 Quote Link to comment
yantosh Posted March 7, 2020 Author Share Posted March 7, 2020 skinny arm and fat tyre fits the bill 3 Quote Link to comment
yantosh Posted March 7, 2020 Author Share Posted March 7, 2020 need rear shock mounts first , had to chop new top mount to rotate, so engine back in to check clearance 4 Quote Link to comment
yantosh Posted March 7, 2020 Author Share Posted March 7, 2020 engine back in, needs a touch more than rotation ... ah well, template time tomorrow Quote Link to comment
yantosh Posted March 9, 2020 Author Share Posted March 9, 2020 top shock mount back together 3 Quote Link to comment
yantosh Posted March 18, 2020 Author Share Posted March 18, 2020 bottom shock mount underway 3 Quote Link to comment
yantosh Posted March 19, 2020 Author Share Posted March 19, 2020 pockets on the underside and shaped to fit the arm a bit better 7 Quote Link to comment
yantosh Posted March 25, 2020 Author Share Posted March 25, 2020 anyone know how hot a TL runs, in Scotland would the top rad be enough with the two fans ? we don,t tend to see Australian weather and they don,t use extra cooling 3 Quote Link to comment
Gammaboy Posted March 26, 2020 Share Posted March 26, 2020 (edited) I'd be inclined to use VFR400 twin rads to make it narrower... (I think it's the 400 rads. A lot of VFR800 guys are using them on strertfightered bikes as an alternative to a TLS or SV rad) Edited March 26, 2020 by Gammaboy 2 Quote Link to comment
yantosh Posted March 26, 2020 Author Share Posted March 26, 2020 prob a good idea, but this build is budget as fuck, and it has a rad, i,m going to to chance my luck with single rad, if it gets too hot i,ll change things wee bit of engraving on yoke caps 3 Quote Link to comment
yantosh Posted March 28, 2020 Author Share Posted March 28, 2020 started on a new muddie, will end up with carbon Quote Link to comment
yantosh Posted March 29, 2020 Author Share Posted March 29, 2020 dragged outside for a quick look before self isolation 9 Quote Link to comment
vizman Posted March 30, 2020 Share Posted March 30, 2020 Dagnammit.....I wanna sv6fiddy now. 1 Quote Link to comment
vizman Posted March 31, 2020 Share Posted March 31, 2020 I know, he waves it under my nose every now and then..... ....spoke to the heeeeeeeed aka Mattman, bottom line is you can run single cooler on the ‘R’ but give him a shout for the details. 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.