Duckndive Posted August 29, 2019 Posted August 29, 2019 (edited) Well I was supposed to be thinning the Flock down but a chance spot on faceache and a trip to Brighton earlier today And oppps got this low miles but very tatty example .."it is complete other bits in boxes" Edited August 29, 2019 by Duckndive 1 Quote
CockneyRick Posted August 29, 2019 Posted August 29, 2019 Tatty is an understatement! Least you might be able to buy Autosol in bulk Quote
Duckndive Posted August 29, 2019 Author Posted August 29, 2019 19 minutes ago, Duckndive said: And oppps got this low miles but very tatty example I did say very tatty Rick Quote
wraith Posted August 29, 2019 Posted August 29, 2019 Looks like its been to near the sea for too long, I think the rot may make up for the low miles Quote
Shill Posted August 30, 2019 Posted August 30, 2019 Nice one! I saw this going on the uk Zuma group, seemed like a good price. What's the plans for it? Quote
Duckndive Posted August 30, 2019 Author Posted August 30, 2019 1 hour ago, Shill said: Nice one! I saw this going on the uk Zuma group, seemed like a good price. What's the plans for it? Even cheaper with a cheeky offer ....Eventually 1216cc and a blow thru wizzer ............ 1st job is to get all the crap off clean the carbs and see if I can get the 750 motor running ...and get the fuel cap open have key but it not playing so may be a drill job Quote
Bow Posted August 31, 2019 Posted August 31, 2019 Better than a blandit . Make a change to see a twinshock project. keep looking at the Inazuma chassis to see how good it would be for a XR replica. Quote
Duckndive Posted September 7, 2019 Author Posted September 7, 2019 Well after taking the carbs off dropping the bowls and taking the slides out and leaving the bodies in a tank of the cheapest coke cola for a few days ... reassembled them this afternoon and with some fresh fuel after a few spins.it fired up .. Aside from the rotten collector blowing it sounds nice and sweet....ran thru the gears ok...just the clutch mech to un seize and I,ll pull it out and decide it's fate... 2 Quote
Stevemilne750 Posted September 11, 2019 Posted September 11, 2019 I'm possibly looking for a 750 engine if it's up for grabs Quote
Duckndive Posted September 12, 2019 Author Posted September 12, 2019 18 hours ago, Stevemilne750 said: I'm possibly looking for a 750 engine if it's up for grabs its out and on the floor with 7 sheared exhaust bolts ... But I,m a long way away "Stratford upon Avon" Quote
Hardassfunk Posted September 13, 2019 Posted September 13, 2019 You have an airbox going spare? Quote
Duckndive Posted September 13, 2019 Author Posted September 13, 2019 4 hours ago, Hardassfunk said: You have an airbox going spare? Yes It looks that way Quote
Duckndive Posted September 14, 2019 Author Posted September 14, 2019 15 hours ago, Hardassfunk said: How much posted? do a deal on your swing-arm where are you ? Quote
Duckndive Posted September 15, 2019 Author Posted September 15, 2019 17 hours ago, Hardassfunk said: In Carlisle Fook that's a trot post it is then Have you found a replacement swing arm yet ? Quote
Duckndive Posted September 15, 2019 Author Posted September 15, 2019 (edited) Finished dismemberment to-day will drop frame and other stuff at powder coaters in the week... have to write a shopping list next PS for info frame is 239mm / 240mm at the swing-arm pivot Edited September 15, 2019 by Duckndive Quote
Fatmama Posted December 26, 2019 Posted December 26, 2019 Looking forward to see this project. Just came back from a 3 day tour with my 12. It's no comparison to any blandit, have 2 x 1200 Inazumas and had a b12s bevore, that's now parts donnor. Quote
Duckndive Posted December 26, 2019 Author Posted December 26, 2019 1 hour ago, Fatmama said: Looking forward to see this project. Project Thread here Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.