clivegto Posted November 20, 2020 Posted November 20, 2020 On 11/20/2020 at 7:49 PM, wraith said: Nice work mate Expand Thanks bud. 1 Quote
clivegto Posted November 21, 2020 Posted November 21, 2020 On 11/21/2020 at 1:30 PM, no class said: Very cool build Clive Expand Thanks man. Quote
clivegto Posted November 21, 2020 Posted November 21, 2020 Mk4 regulator bracket, makes it 5mm higher and brings it 6mm closer to the sub frame from where I started with mk1 bracket. This gives clearance for all 4 pipes as well as room to adjust the top locking mut. 2 Quote
370steve Posted November 21, 2020 Posted November 21, 2020 GPS speedo not legal mate!! just saying Quote
clivegto Posted November 21, 2020 Posted November 21, 2020 (edited) On 11/21/2020 at 3:25 PM, 370steve said: GPS speedo not legal mate!! just saying Expand Not to bothered mate, fitted one to the Turbo Scratcher in spring, works a treat. No tunels or tall buildings round hear to upset it lol Edited November 21, 2020 by clivegto 2 Quote
clivegto Posted November 21, 2020 Posted November 21, 2020 Modified the electronic tray that came with the frame that fits under the tank. Had to cut a bit out to alow the breather pipe from the rocker cover to poke through so the tray could sit flat on the frame mounting tabs. 2 Quote
clivegto Posted November 21, 2020 Posted November 21, 2020 Looks like the old coils were mounted hear, will try to use as many of the existing holes in it as possible. Made some 14mm spacors up to mount the coils to. Tank should clear the coils fine. 4 Quote
Wagola Posted November 21, 2020 Posted November 21, 2020 That is looking good almost complete and ready to press the starter button !? Hope it looks better with the tank on but that seat looks like it came off one of your tractors in the background !! 1 Quote
clivegto Posted November 21, 2020 Posted November 21, 2020 On 11/21/2020 at 7:21 PM, Wagola said: Seat looks like it came off one of your tractors in the background !! Expand 1 Quote
Wagola Posted November 22, 2020 Posted November 22, 2020 Its just the way the seat sits perched on its rails with no tank or side panels. Still looking forward to seeing the bike in the flesh sometime hopefully. Quote
Dezza Posted November 22, 2020 Posted November 22, 2020 (edited) That alloy electrics tray is going to get mightily hot. The one supplied with a frame kit from Harris was the same shape but made from fibreglass instead. Edited November 22, 2020 by Dezza Quote
clivegto Posted November 22, 2020 Posted November 22, 2020 On 11/22/2020 at 11:44 AM, Wagola said: Its just the way the seat sits perched on its rails with no tank or side panels. Still looking forward to seeing the bike in the flesh sometime hopefully. Expand Fits quite neat with seat unit on I thought 1 Quote
clivegto Posted November 22, 2020 Posted November 22, 2020 On 11/22/2020 at 1:01 PM, Dezza said: That alloy electrics tray is going to get mightily hot. The one supplied with a frame kit from Harris was the same shape but made from fibreglass instead. Expand Its a fair point is that. It did have gsxr750 motor in last with same tray but engine was slightly lower. Might fit some heat shield underneath. Quote
clivegto Posted November 22, 2020 Posted November 22, 2020 Have left a air gap between the coils and the tray. 3 Quote
Wagola Posted November 22, 2020 Posted November 22, 2020 On 11/22/2020 at 1:46 PM, clivegto said: Fits quite neat with seat unit on I thought Expand Yeah, agreed. That looks much more motorcycle !! Quote
clivegto Posted November 22, 2020 Posted November 22, 2020 Fitted 4 rubber grommets to the tank undertray just to lift it a bit really. Also fitted the ignition to the side of the tray. 4 Quote
clivegto Posted November 23, 2020 Posted November 23, 2020 O ring arrived from Germany today for the clutch cover got a spare as well, best not put it in to safer place Cut the taylo leads to length and fitted them. 4 Quote
370steve Posted November 23, 2020 Posted November 23, 2020 On 11/23/2020 at 5:24 PM, clivegto said: . Expand Might want to put a grommet in that hole the leads goes through mate! chaffing and all that Quote
clivegto Posted November 23, 2020 Posted November 23, 2020 (edited) On 11/23/2020 at 6:54 PM, 370steve said: Might want to put a grommet in that hole the leads goes through mate! chaffing and all that Expand There ya go job jobed Loom is going through there as well Edited November 23, 2020 by clivegto 4 Quote
clivegto Posted November 25, 2020 Posted November 25, 2020 On 11/25/2020 at 5:55 PM, zed said: Tidy Expand Cheers man. Quote
clivegto Posted November 27, 2020 Posted November 27, 2020 (edited) Wasn't happy with the rocker cover breather so made a new one out of 13mm id silocon pip 15mm copper sleeves stuck together with flexible polyurethane adhesive for the first part. 2nd part is back to an8 fittings. Edited November 27, 2020 by clivegto 7 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.