busa ash Posted July 19, 2019 Share Posted July 19, 2019 Spoke with yoshi johnny and did a deal on his project , lots ask about special frames and want them , but dont commit to buy when they see them , if only it was cheaper ? nearer ? can we do mates rates ?, NO CASH , this is a good build and with just the right amount of cool pics later 1 Quote Link to comment
baldrick Posted July 19, 2019 Share Posted July 19, 2019 Havnt you got enough harrises lol. lets see the pics, is it the blue and silver one, with the guage in the tank? Quote Link to comment
busa ash Posted August 6, 2019 Author Share Posted August 6, 2019 Here we go then 2 Quote Link to comment
busa ash Posted August 6, 2019 Author Share Posted August 6, 2019 I have bought a swingarm from a clive via swirl s original green harris Gurls blouse nc29 full arm 3 Quote Link to comment
busa ash Posted August 10, 2019 Author Share Posted August 10, 2019 The bit I hate the most wiring 3 Quote Link to comment
SiBag Posted August 12, 2019 Share Posted August 12, 2019 Is that a Mag-II or a Mag-I ? Tank is def a Mag-I Quote Link to comment
busa ash Posted August 12, 2019 Author Share Posted August 12, 2019 (edited) magnum 2 with magnum 1 tank si 8 hours ago, SiBag said: Is that a Mag-II or a Mag-I ? Tank is def a Mag-I Edited August 12, 2019 by busa ash Quote Link to comment
busa ash Posted August 12, 2019 Author Share Posted August 12, 2019 Been to my mates house to have a play on his old milling machine Rsv mille rear brake set up I am trying to use with gsxr disc and saxon wheel , tyre too wide it's a 190 bit tight and will need to have z proper look in the daylight 3 Quote Link to comment
busa ash Posted August 14, 2019 Author Share Posted August 14, 2019 Mirrors from a long lost project Quote Link to comment
busa ash Posted August 14, 2019 Author Share Posted August 14, 2019 Fairing looking for a headlight with side light for mot 1 Quote Link to comment
busa ash Posted August 14, 2019 Author Share Posted August 14, 2019 Slabby rear light for the harris seat unit Quote Link to comment
busa ash Posted August 14, 2019 Author Share Posted August 14, 2019 Seat pad may be redone but for now it gives the right look 1 Quote Link to comment
caferacerdan Posted August 14, 2019 Share Posted August 14, 2019 side lights arent a requirement for an MOT. only need low and main. believe the vfr or cbr400 headlights have low and high built in 1 Quote Link to comment
clivegto Posted August 15, 2019 Share Posted August 15, 2019 (edited) Can you put a notch in the arm with a slightly smaller tyre as well Ash. Edited August 15, 2019 by clivegto 1 Quote Link to comment
busa ash Posted August 16, 2019 Author Share Posted August 16, 2019 Just found a 20mm axle think it's a yamaha one but it's better than the zooki one I was going to use Quote Link to comment
busa ash Posted August 16, 2019 Author Share Posted August 16, 2019 Wiring and more wiring 1 Quote Link to comment
busa ash Posted August 18, 2019 Author Share Posted August 18, 2019 Found a spindle for the rear swingarm think it's from the front of a yam 20mm Quote Link to comment
busa ash Posted August 18, 2019 Author Share Posted August 18, 2019 Well a really good day yesterday loom all connected and tested . Routed just need too loom tape it now . Also ordered the oil fittings for the take off point behind the motor 1 Quote Link to comment
busa ash Posted August 22, 2019 Author Share Posted August 22, 2019 Ta d dah arrived this morning 2 Quote Link to comment
busa ash Posted August 27, 2019 Author Share Posted August 27, 2019 Bit of time working on bike .. Soooooo the foow king thing wont fit one fitting too close to crankcase and other smack bang in middle of clutch cable route Quote Link to comment
Dezza Posted August 27, 2019 Share Posted August 27, 2019 Switch to large banjo fittings? Quote Link to comment
busa ash Posted September 1, 2019 Author Share Posted September 1, 2019 The saga continues lol sent 2x 90 degree fittings Quote Link to comment
busa ash Posted September 1, 2019 Author Share Posted September 1, 2019 First fitting hits second fitting ffs so ordered an 8 to an8 coupler see if that works Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.