Swirl Posted January 6, 2017 Posted January 6, 2017 should be good for my played with 1045 then 1 Quote
busa ash Posted January 15, 2017 Author Posted January 15, 2017 Carbs arrived and are a great fit plug and play . And spun engine round after moving bike that's balancing on axle stands as swingarm is away being worked on 1 Quote
Pheasantplucker Posted January 16, 2017 Posted January 16, 2017 Like the build, I would have to sell the missus and a kidney .................... Would you mind measuring the frame tubes! I'm interested to know what diameter tube Mr Harris uses. Quote
busa ash Posted January 16, 2017 Author Posted January 16, 2017 messages sent mate ref frame dimensions Quote
busa ash Posted January 18, 2017 Author Posted January 18, 2017 (edited) Just writing out a list of parts and what manufacturer they or suzuki , yam hon kaw mv triu While having a brew . Got nearly everything I think . Just waiting for a few little bits of engineering. Then can push on . Have too have a new bottom bolt on rail made for the sidestand , so will fit a modern side stand while I am at it part of its evolution Edited January 18, 2017 by busa ash missing text Quote
Blue Posted January 18, 2017 Posted January 18, 2017 On 29/12/2016 at 8:16 PM, busa ash said: What are these fittings called & where from? Thanks 1 Quote
busa ash Posted January 18, 2017 Author Posted January 18, 2017 Blue bought from Eblag . Waterproof amp fittings iirc I bought lots of diffrent combinations 2 way ,3 way up too 9 way From China They are also available from towtronics and vehicle wiring products but at way more 2 Quote
Pheasantplucker Posted January 19, 2017 Posted January 19, 2017 looking forward to seeing this in one piece, even pre paint. 1 Quote
busa ash Posted January 25, 2017 Author Posted January 25, 2017 New bits arrived from Robinson of Rochdale with 15% discount thanks lee and yj Cam cover Bolts ,rubber washers and 8 x clamps for carb rubbers and carbs .few quid but it's the right way to build up a special build 2 Quote
busa ash Posted February 1, 2017 Author Posted February 1, 2017 just dropped off a few parts at powder coaters too see if the colour i chose works ? only few parts as if it doesnt i can try again mid blue then laqured for side stand as its big and will give me an idea if it works or not also carb tops and two rails that hold them , efe cam cover and breather cover in a satin textured look two outer cases in satin black 1 Quote
busa ash Posted February 5, 2017 Author Posted February 5, 2017 Carbs re done with new Allen head stainless Bolts 2 Quote
busa ash Posted February 8, 2017 Author Posted February 8, 2017 Sat in a villa in portugal looking at my build thread . Need some good luck as i am surrounded by bad at the moment Quote
Swirl Posted February 9, 2017 Posted February 9, 2017 whats the weather like Ash, just seen ye carbs on the laptop, usually on the phone, they look different 1 Quote
busa ash Posted February 11, 2017 Author Posted February 11, 2017 swirl home now , weather was great Quote
Diebythereaper Posted February 12, 2017 Posted February 12, 2017 Nice job on carbs looks smart! 1 Quote
busa ash Posted February 13, 2017 Author Posted February 13, 2017 some more teething trouble with swingarm so has been given to a mate who is hoping too cheer it and up so i can move forward . rearsets too 1 Quote
busa ash Posted February 23, 2017 Author Posted February 23, 2017 Many thanks to si bag and gsxr Sam for sorting my rearsets plates perfect fit and finish . And hopefully my swing arm might be ready soon too 1 Quote
SiBag Posted February 23, 2017 Posted February 23, 2017 And they look even better on. Iv shown you mine now you show me yours... I have to admit Sam did a cracking job. 1 Quote
busa ash Posted February 23, 2017 Author Posted February 23, 2017 Here you go simon great fit . Also gave the cam cover a bit of crinkle finish Quote
Swirl Posted February 23, 2017 Posted February 23, 2017 will have to look into something similar for mine, to accommodate my gammy legs, already got big bars to accommodate my gammy arms and back 1 Quote
SiBag Posted February 23, 2017 Posted February 23, 2017 (edited) Cam cover looks the muts nuts, and the Titanium / Grey Gilles suite the plates.. Edited February 23, 2017 by SiBag 1 Quote
busa ash Posted February 23, 2017 Author Posted February 23, 2017 Thanks mate . Its coming together well now with the oss network of friends as always Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.