MotoRoboto Posted April 13 Posted April 13 Hello, Just installed cams in the 1100 I'm using for my 7/11 project, will have updates later, and there is zero cam chain slack. 22 links, arrows where they need to be, grooves at end of cam in proper position, rotor lined up, idler installed. Turns over by hand reasonably well. When I pushed on the chain guide thru the tensioner hole there was no play at all. The '86 750 that was in it was high miles and had a lot of slack after cam install. Maybe this is just a good condition cam chain and I'm not used to it? I can't help but think something isn't right tho. Run out of ideas. Any suggestions on things to look at? Quote
Gixer1460 Posted April 13 Posted April 13 Don't take as gospel but I think the 1100 is 21 pins and 750 is 22 ? ? ? Brain is old and memory fading + i'm not near a manual presently! Quote
MotoRoboto Posted April 14 Author Posted April 14 18 hours ago, Gixer1460 said: Don't take as gospel but I think the 1100 is 21 pins and 750 is 22 ? ? ? Brain is old and memory fading + i'm not near a manual presently! It's flipped. Had three manuals. A factory manual, an old first gen only Haynes and a first thru third gen manual. I ended up pulling the cams and holding the cam chain while I rotated engine to make sure it was on crank correctly and not kinked. Put cams in while holding cam chain taught. Redid everything. Slack was the same. Just how it is I guess. Spun fine later when more fully assembled. Quote
george 1100 Posted April 14 Posted April 14 I can't remember exactly but might be a cam sprocket thing. Where did those cams come from? Quote
Dezza Posted April 14 Posted April 14 If using 750 j,k cams in a GSXR1100 do you have to use the 1100 cam sprockets? Quote
george 1100 Posted April 14 Posted April 14 1 hour ago, Dezza said: If using 750 j,k cams in a GSXR1100 do you have to use the 1100 cam sprockets? Yes 2 Quote
MotoRoboto Posted April 14 Author Posted April 14 7 hours ago, george 1100 said: I can't remember exactly but might be a cam sprocket thing. Where did those cams come from? D0thead and cams. I put some stock cam sprockets on it and same situation. My guess is just old engine was really worn out. Quote
MotoRoboto Posted April 14 Author Posted April 14 (edited) 7 hours ago, Dezza said: If using 750 j,k cams in a GSXR1100 do you have to use the 1100 cam sprockets? I looked into that and the cam sprocket part numbers are all the same. Changing sprockets made no difference in slack. Maybe the d0thead is slightly taller. Edit: Scratch that, yes they are different but I got some stock 1100 cam sprockets just in case. The cams are from a d0thead 750 BUT they were in the 1100 so I'm assuming the adjustable cam sprockets were correct for that engine. Either way I didn't use them and the stock ones provided the same slack. Edited April 14 by MotoRoboto Quote
george 1100 Posted April 15 Posted April 15 Might have something to do with the dot head. From memory the valves are slightly longer so maybe the cam locations are slightly higher. Ive never done a dot head but plenty here have. Maybe you could machine down the cam chain roller spacers Quote
MotoRoboto Posted April 15 Author Posted April 15 18 minutes ago, george 1100 said: Might have something to do with the dot head. From memory the valves are slightly longer so maybe the cam locations are slightly higher. Ive never done a dot head but plenty here have. Maybe you could machine down the cam chain roller spacers That was my next guess from what I've read about that head. I'll look into that. It's currently running with no abnormal noise. Quote
Nik Posted April 15 Posted April 15 Most people fit DOT heads to Bandit 1157s (with their different cam chain setup, with hyvo chain and no idler). It may be that the DOT head's got a slightly different geometry, and maybe the Bandits are more forgiving and the difference doesn't get noticed when fitting them to Bandits. Just a guess. 1 Quote
Duckndive Posted April 15 Posted April 15 Never had any cam chain issues when i,ve done them ... always used slotted sprockets and leave tensioner out until are cam,s in and then dial them in 1 Quote
MotoRoboto Posted April 15 Author Posted April 15 1 hour ago, Duckndive said: Never had any cam chain issues when i,ve done them ... always used slotted sprockets and leave tensioner out until are cam,s in and then dial them in That's good to hear. Oddly the cams that cam out of the engine had slotted sprockets but were so far off I went back to stock. Maybe some winter I'll put them back in. Quote
MotoRoboto Posted May 23 Author Posted May 23 Added spacers below the cam chain idler. It cleared the cover and added enough slack. Has been good to go and zero issues. Thanks Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.