Q on mounts for 1127 to Slabby 7 frame?

[CockneyRick]

Got plenty of mounts & have sort of whittled it down to these 3 pairs. So my guess is as follows:

Top pair (black) are bottom mounts cos of hole for fairing mount?

Middle pair (Silver) front mounts? Bottom edge longer than other sides & hole at top biggest. Although they have fairing holes, i do have plenty without?

Bottom pair (shiny) Cos of engraving, i guess rear mounts so the R logo is facing as written.Large hole to L/R?

 

Top & middle could easily be other way round to my thoughts?

 

Also when fitted, are there any spacer(s) Needed to mount at rear bolts for an 1127 into the Slabby 750F/G frame?  These are something i don't have!

Edited May 3, 2017 by CockneyRick
mod

[Blue]

I think you mean the spacer in my picture. There's 1 each side of the engine, top rear mount. https://www.cmsnl.com/suzuki-gsxr750r-1986-g-usa-e03_model16088/partslist/BLCK0018.html#results & https://www.cmsnl.com/suzuki-gsxr750r-1986-g-usa-e03_model16088/partslist/BLCK0010.html#results

 

Edited May 4, 2017 by Blue

[CockneyRick]

Yep, didn't know there was 2!  Anybody got any spare?

[Blue]

Wouldn't take much to make some

[CockneyRick]

2 hours ago, Blue said:

Wouldn't take much to make some

If i knew the size

 

[Blue]

Lengths 50 & 59 mm hole in centre 10.5mm

Edited May 5, 2017 by Blue
Added pic

[CockneyRick]

[Blue]

Are you able to sort?

[CockneyRick]

I may know a man, unless you..........

[Blue]

I'll see if i've got any material , if so I'll start making some

[CockneyRick]

Before you do, let me check the gaps on either side, as every thing seems slightly off when i put this 1127 lump in the frame. Front mounts (4 types i have) & none fit? So need to double check all the other mounts & gaps

[CockneyRick]

Done measurements & this is what i have need of: 

1x 35mm spacer for bottom rear mount

1x 50mm spacer for top LH rear mount

1x 55mm spacer for top RH rear mount

Can only figure that the 1127 (teapot) lump may be slightly different to the std 1127?

[CockneyRick]

No need for the fancy end shape, just a std spacer will do

[Captain Chaos]

27 minutes ago, CockneyRick said:

the 1127 (teapot) lump may be slightly different to the std 1127?

no

[CockneyRick]

Very odd, wonder why front mouts don't fit & back spacers are different 50 & 55mm to what i've been told?  Any chance you have pics of all the front/bottom/back mounts in place?

[Mr Cosmo]

Black ones are the lower mounts Rick,

[Blue]

Only shows 1 mount but that could be due to the shape of the frame https://www.cmsnl.com/suzuki-gsx1100f-1990-l-e01-e02-e04-15-16-17-18-21-22-24-25-34-39-53_model13748/partslist/FIG-04.html#results

Edited May 8, 2017 by Blue

[CockneyRick]

3 hours ago, Blue said:

Only shows 1 mount but that could be due to the shape of the frame https://www.cmsnl.com/suzuki-gsx1100f-1990-l-e01-e02-e04-15-16-17-18-21-22-24-25-34-39-53_model13748/partslist/FIG-04.html#results

It's not going in an GSX1100F frame. It's that engine going in a GSXR750F frame  

[Blue]

Yes I gathered that

[CockneyRick]

And that has 2 spacers

[clivegto]

Engine in my 750 frame is 1100f slabby engine mounts did make some of the spacers up as didn't have them all. Some pics maybe not the best to see what go's where, I just did it by trial & error. Pics front bottom back.

[dupersunc]

All the oil cooled crank cases are the same regarding engine mount positions and widths, the only variants are the 1127 have larger bolts in the rear mounts.   Spacers should be the same width, between engines.  Mounting plates aren't interchangeable between 1100 and 750 slabbie frames. The top rears you have with the etched  "R" are from an 1100 slabbie, they are thicker than standard mounting plates, hence the need for different spacers.

HTH.

[CockneyRick]

If you look at Clivegto's pics, my rears & lowers are the same, the R logo ones are huge & don't fit anywhere? As for fronts, i have 4 types (inc lower/rears) and all of em are too big to fit.

Seen some on eblag that are a lot smaller, so mebbe these are what i need?

Can anyone tell me the gap at front of engine/camcover to slabby frame gap? Mine seems very close, 4-5mm tops!

[CockneyRick]

And yes i used to mess with Oilcooled lumps, but went to Air for last 10 yrs, so trying to remember all that shit i forgot!

[clivegto]

I have some out of a frame at the moment I could draw round them on some card & post it to you.