jimbob1975 Posted April 22, 2020 Posted April 22, 2020 Hi All, Tried to start bike yesterday and cylinders 2 and 3 have no spark.I have checked ht leads they are ok. checked coil by swapping for a known working coil. orange and white supply has over 12v supplied to coil.What next?How can I test the CDI.Advise greatly appreciated.Thanks Quote
Captn Posted April 22, 2020 Posted April 22, 2020 You need an analog voltmeter or 12vdc test light. Connect the voltmeter across the primary ( red lead to org black lead to black) crank the engine for 5 to 7 seconds and watch the meter needle. It should move from 0 to 10 volts during the cranking. If not then the CDI is not switching the primary and the coil will not fire. I will assume you've already verified that 1 and 4 are firing? Quote
stellafella Posted April 22, 2020 Posted April 22, 2020 (edited) have you swapped it with the working coil on the bike ? Edited April 22, 2020 by stellafella Quote
jimbob1975 Posted April 22, 2020 Author Posted April 22, 2020 Hi yes 1 and 4 the outer cylinders running as bike sounds like a twin and verified by feeling the hot exhaust down pipes two inner pipes stone cold. Have pulled plugs and cranked over with plugs resting on top of engine. Zero sparks. Quote
jimbob1975 Posted April 22, 2020 Author Posted April 22, 2020 Captn thanks for the reply not sure which wires you mean. I have blue and yellow. Green and black coming from ignition pickup into cdi. Then four wires coming out of cdi to coil orange/white positives for coils and other three are black/yellow and black/white to coils and a white. Thanks Quote
Gixer1460 Posted April 22, 2020 Posted April 22, 2020 (edited) 4 out of CDI - Orange / white = 12v + (single wire splits in loom to both coils), Black / white = ground / earth to frame / chassis, Black / yellow = Coil 2/3 & White = Coil 1/4. 5 out of pick-up case - Blue + Yellow and Green + Black are pick-up signals (two pick-ups) and Green/yellow? = Oil pressure switch signal to dash. This is for Slabby motors, Slingshot motors are similar except one pick-up is deleted so no Green + Black wires present. Edited April 23, 2020 by Gixer1460 Corrected for slabby / slingshot wiring differences Quote
jimbob1975 Posted April 22, 2020 Author Posted April 22, 2020 4 hours ago, Captn said: You need an analog voltmeter or 12vdc test light. Connect the voltmeter across the primary ( red lead to org black lead to black) crank the engine for 5 to 7 seconds and watch the meter needle. It should move from 0 to 10 volts during the cranking. If not then the CDI is not switching the primary and the coil will not fire. I will assume you've already verified that 1 and 4 are firing? Hi have worked it out thanks.The coil that supplies cylinders 1 and 4 the meter is going up and down like crazy when turning over on starter but other coil nothing on the meter.Its looking like a faulty cdi? Any newer cheaper alternatives?thanks 3 hours ago, stellafella said: have you swapped it with the working coil on the bike ? Quote
Captain Chaos Posted April 22, 2020 Posted April 22, 2020 don't Slabbies have two pick-up coils? One could be faulty. Quote
Captn Posted April 22, 2020 Posted April 22, 2020 You've determined the CDI is not firing 2 and 3 cylinders coil. Now we need to see if the pulse from the ignition pickup is coming into the CDI. Refer to @Gixer1460comment about the ignition pickup wire color code. This is the next test point. You will need to check resistance measured in ohms as well as signal that is generated. Be back shortly with some numbers. Quote
jimbob1975 Posted April 23, 2020 Author Posted April 23, 2020 Hi Captn I have taken the engine cover off to inspect the pick ups and I have two pickups and four wires. Two going to each coil.Black and Geen to one and Yellow and Blue to the other.I have tested for resistance and both read the same.How to check for trigger readings? If I replace the cdi is there anyting newer I can use other than Dynatek?Thanks Greatly. Quote
davecara Posted April 23, 2020 Posted April 23, 2020 14 hours ago, Gixer1460 said: 4 out of CDI - Orange / white = 12v + (single wire splits in loom to both coils), Black / white = ground / earth to frame / chassis, Black / yellow = Coil 2/3 & White = Coil 1/4. 3 out of pick-up - Blue + Yellow are pick-up signal and Green/Black = Oil pressure switch signal to dash. If its a slabby then it'll have 5 wires coming from the pickup area Quote
davecara Posted April 23, 2020 Posted April 23, 2020 19 hours ago, jimbob1975 said: Hi All, Tried to start bike yesterday and cylinders 2 and 3 have no spark.I have checked ht leads they are ok. checked coil by swapping for a known working coil. orange and white supply has over 12v supplied to coil.What next?How can I test the CDI.Advise greatly appreciated.Thanks If you know your coils are in good working order, then get the ignition pickup cover off and check continuity between the CDI and the 2 sets of pick up wires and the gap between the VR sensors and the trigger wheel. If youre happy with those I'd try a good known CDI and that'll narrow your problem down 1 Quote
Gixer1460 Posted April 23, 2020 Posted April 23, 2020 30 minutes ago, davecara said: If its a slabby then it'll have 5 wires coming from the pickup area Thank you - i've edited my post! 1 Quote
Captn Posted April 23, 2020 Posted April 23, 2020 Yellow and blue wires are the pick up signal. Use the analog meter with it set to volts AC. Connect red and black meter leads to the yellow and blue pick up leads. Crank the engine for about 10 seconds and watch the meter needle. It should move from 0 to 2 or 3 volts in a rapid sweeping motion. If that tests ok the pick up coils are ok. Verify the wiring between the pick up connection to the CDI plug is good. Verify the black wire between the CDI plug to ground is 1 ohm or less. Quote
Captn Posted April 23, 2020 Posted April 23, 2020 I do not know of another ignition system for these bikes other than DynaTek. I have ben running one and it has been flawless. I could not find a working Suzuki CDI so I decided to go to aftermarket. I have seen a common failure with the OEM CDI of the 2 and 3 cylinder transistor. This causes the exact problem you are having. Quote
jimbob1975 Posted April 23, 2020 Author Posted April 23, 2020 Thanks Captn you have all been a great help looks like another cdi it is Quote
jimbob1975 Posted April 23, 2020 Author Posted April 23, 2020 I will see about going down the Bandit 1200 route with a bandit cdi and ignition pick up etc Quote
jimbob1975 Posted April 27, 2020 Author Posted April 27, 2020 Hi All Just an update have sourced a working cdi and tried it and still the same so now looking like the ignition coil pickup.Obviously on mine I have two pick up coils. Could I use a later coil say from a bandit 1200 or a later model gsxr that have the single coil as they look identical?Cheers Thanks Quote
jimbob1975 Posted May 11, 2020 Author Posted May 11, 2020 Hi ,After much head scratching and fault finding, finally got to the bottom of why cylinders 3+4 were not sparking. I had fitted an after market modern set of clocks.Somehow I had wired the trigger wire that comes from cylinders 2/3 coil into the clocks...... somewhere it wasn't meant to go! This resulted in cancelling out the signal, hence no spark! Now corrected and all four pistons firing!Hope this helps somebody else out! 3 Quote
Captn Posted May 11, 2020 Posted May 11, 2020 (edited) @jimbob1975. Thanks for posting your finding. That is the key to helping out, the feedback is important. Good find!! Edited May 11, 2020 by Captn 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.