Jump to content

K1-K3 headers


Venom

Recommended Posts

Posted (edited)

Yes.

But you will have to give them a tweak. Spacing between the down pipes is different, so you have to pull them out.

And they sit a little low, so they need bending up under the sump. A blow torches, a car jack and some swearing and ya sorted.

There should be loads on here about doing it.

Edited by SiBag
  • Like 2
Posted
17 hours ago, SiBag said:

Yes.

But you will have to give them a tweak. Spacing between the down pipes is different, so you have to pull them out.

And they sit a little low, so they need bending up under the sump. A blow torches, a car jack and some swearing on ya sorted.

There should be loads on here about doing it.

thank you for info

 

  • 2 weeks later...
Posted
8 hours ago, boilerdude said:

So they also fit blandit?  Worthy upgrade for cheap?

Worth it just to get rid of the mild steel scrap collector thats designed to rot out and split the serviceable stainless exhaust in 2.

Posted (edited)

I have a GSXR1100 Akrapovic system on my B12 engined GS, fits very well, just hangs a little low for some folk! but that is due to the adapters needed for my frame clearance, you shouldnt have that problem with a stock engine in a stock frame  :)

100_4266.JPG

Edited by 370steve
  • Like 1
Posted (edited)

gsxr 1000 exhaust this thread is about. Yes we all know a gsxr1100 exhaust fits. this is about spreading apart the spacing and retrofitting gsxr ONE THOUSAND headers on a bandit. ONE THOUSAND. 

Hence the K1, K2, K3

Edited by boilerdude
Posted

actually that was useful information irregardless. If a gsxr 1000 exhaust hangs low on an 1100. And a gsxr 1100 exhaust hangs low on a bandit. Then a gsxr 1000 exhaust on a bandit should hang really really low. That is good information to have.

Posted
6 hours ago, boilerdude said:

actually that was useful information irregardless. If a gsxr 1000 exhaust hangs low on an 1100. And a gsxr 1100 exhaust hangs low on a bandit. Then a gsxr 1000 exhaust on a bandit should hang really really low. That is good information to have.

Erm no 

Look at the pic, he has about an inch to 2 inches of extra pipe where it fits to the motor.

You can get the thou headers quite tight to the dump with a bit of effort.

Posted (edited)
On 11/05/2016 at 2:08 PM, SiBag said:

Yes.

But you will have to give them a tweak. Spacing between the down pipes is different, so you have to pull them out.

And they sit a little low, so they need bending up under the sump. A blow torches, a car jack and some swearing and ya sorted.

There should be loads on here about doing it.

^^ this on a gsxr1100, i will soon be trying on my bandit so will report back with measurements etc 

Edited by fish91
Posted

I took the easy way out. Talked with a buddy of mine who just so happens to have an extra b12 yosh header. I just swapped the 750m carbs on my bandit. I'm trading him my old bandit carbs..

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...