harris magnum 2 katana 1100 motor

[busa ash]

Bit more sourced for this build , one off harris yokes, and gsxr 1100 slingy clocks hoping to get a new bracket fabricated so it fits to fairing mount 

 

[clivegto]

Very nice indeed 

[clivegto]

@busa ashcan you tell me what size the back disc is please. 

[busa ash]

1 hour ago, clivegto said:

@busa ashcan you tell me what size the back disc is please. 

240mm rear disc suzuki bandit 1200 fitment 

[busa ash]

Few set backs a few bits done , 

Dropped the oil threads came out with the drain plug ,

Took sump off and cleaned it to send out for repair think I will remove oil pick up bolt 2 snaps in the casings so now front end is off and cant lean bike over to be able to see the snapped bolt . Need to refit forks and wheel etc so I can sort this before I can move on 

 

Mudguard and seat collected by painter as he passes on way too work 

[clivegto]

That's a proper pain you don't need Ash. 

[Dezza]

Same as always: 2 steps forward, 1 step back or even 1 step forward, 2 steps back. We feel your pain

[busa ash]

Thanks guys lock down is helping get bits done , seat pad has been re done , seatunit and mudguard will be back this week so fingers crossed for a few better pictures of my progress weekend 

[busa ash]

Fitting of the flatslides into et inlet rubbers,  takes little finess

[busa ash]

Fitted and I like the look 

[busa ash]

Fitted and I like the look , also side case finally fitted after lots of swearing as the inside of the casing was cast wrong so plenty of work with a dremel tool 

[busa ash]

Fitted and I like the look , also side case finally fitted after lots of swearing as the inside of the casing was cast wrong so plenty of work with a dremel tool 

 

Side stand done with bigger foot

[busa ash]

Seat is shaped at front so dzus fasteners can be fitted 

[Dezza]

Will the throttle cable adjuster foul the base of the tank? I ask as I know the bottom of a Magnum tank is close to the frame cross rail and there's just enough room for a cable to fit between the frame and tank.

[clivegto]

Biger foot on the side stand is a really good idea. 

[SiBag]

Looking good ash..

[busa ash]

On 4/29/2020 at 4:16 PM, Dezza said:

Will the throttle cable adjuster foul the base of the tank? I ask as I know the bottom of a Magnum tank is close to the frame cross rail and there's just enough room for a cable to fit between the frame and tank.

It's close but all good dezza

[busa ash]

Few more bits coming together,  slabby rear light fitted , colour scheme coming together now 

[busa ash]

Seat upholstered by rydale upholstery elvington . Ì am happy with build few niggles but it's the way of any build 

[busa ash]

As I dont like to sticker bomb a build I am going to wait till bike is off the ramp and can get some perspective , stand back and look from diffrent angles

[busa ash]

Glad I waited now l, wasn't happy with width of stripe also ordered a smaller  25mm for mudguard .

As the other would not lay flat because of double radius of mudguard 

[busa ash]

Also sump back from having a timesert done future proof now fingers crossed 

[Dezza]

From where did you get the go-faster speed stripes?

[busa ash]

On 5/15/2020 at 10:25 AM, Dezza said:

From where did you get the go-faster speed stripes?

Eblag dezza gulf stripe decal Tommy kat is the seller really good quality 

Edited May 26, 2020 by busa ash
Spelling

[busa ash]

Well decided on something diffrent for my tank taken it to a sign writer who is going to do some artwork on the tank !, i am in no rush as just been furloughed  , and also going to change the electrical set up under the tank