[Digital speedo. Can't get rev counter to work]

Anyone had any luck yet?  

Mine might be lucky and get the hammer treatment!!!

[RF900 race bike has it's first shake down at Cadwell Park]

Loving this. Spec plz. 

[750 WR Carb Help!!]

I've uesd the outer bit of a rivet to do the same. Just tapped the inner bit out and bingo. But do countersink on under side like skunkrider2 says. 

I used a rubber bung off daughters pen to seal it until she demanded it back.  Apparently the blue tongue didn't go well  with her pink shoes! 

Cant please the kids nowadays.

[Digital speedo. Can't get rev counter to work]

Yes need to know the frequency output of ecu so one can adjust values. With three 1k resistors and three caps at 10nf dont work either. And maplins dont stock more then two caps at atime!!! Not my local one. Anyways, use the net to order next time. Some nice person decided it were funny to puncture my rear tyre while in shop. Grŕrrŕrrrrr no screw or nail. Looks more like burn hole.

[Digital speedo. Can't get rev counter to work]

Does anyone know the exact output frequency of the ecu ??

[B6 fork caps difference 95 & 2004]

Guessing they're some differents from the 2000 onwards as they list them seperate. But weather they fit some one may be along. Same part no tho so guessing internals have changed.

http://www.ronayers.com/oemparts/p/suzuki/51351-10d00/-cap-fork

[Digital speedo. Can't get rev counter to work]

Still not working. Hmmm. Going to try square wave to sine wave convertor. 

[Digital speedo. Can't get rev counter to work]

The wire wrapped round the coil to the input for the tachograph feed.. when I was holding the the wires before I connect them the tachograph burst into life. 

[Digital speedo. Can't get rev counter to work]

Tried wrapping wire round no 1 coil it works but only if I touch the connection. Seems I am an inductor!  I'll try a few more turns or may less see where it goes.

[Digital speedo. Can't get rev counter to work]

Cool. I'll give it a try.

[Slingshot valves in 750L]

750L valves are specific to that head only. As per microfishe. Don't list fitting to any other models. 

12912-17D00 ex valve part no.

12911-17D00 in valve part no. 

Hope that helps. 

[Digital speedo. Can't get rev counter to work]

Hi caferacerdan. Can yer remember the values of said resistors? 

[Digital speedo. Can't get rev counter to work]

Cant wrap wire around ht lead as i use coil sticks tho maybe it might work if i wrap it round a stick. Hmmmmm.

[Digital speedo. Can't get rev counter to work]

1 hour ago, Danm54 said:

You do have to set the clocks for the amount of cylinders, hi or lo side of coil etc.

 

If you search for a company called digital speedos then there are a few manuals on there with an explanation how the clocks are set up.

I've done all of them methods. Maybe I'll  try using a capacitor and resistor.  If not maybe a stack or motec might fix it! 

[Gsxr1000 master cylinder]

Same as far as microfishe shows. 

[Digital speedo. Can't get rev counter to work]

Have set the clocks 1 and  2 and 4cyl but still nowt.

[Digital speedo. Can't get rev counter to work]

I'll do a lookie on that site. Let ya know the out come. Cheers.

[Digital speedo. Can't get rev counter to work]

Tried ecu pick up. Tried +12 and -12 off coils.  Grrr nowt. Seached net but nowt. Grrrrrrrrrrrtr.

[Digital speedo. Can't get rev counter to work]

One off these speedos. Tried asking company what input required but no reply.  Grrrr. 

 

[Digital speedo. Can't get rev counter to work]

Hi everyone. Nice to see old skool back. 

Having problem with getting rev counter working on gsxr750wn. Old counter works fine but can't  seem to get a signal to operate the new digital one. Its one of them koso copy from China.  Anyone tried one? Speedo only seems to work when it want too! 

My bike below at Snetterton. 

Any help on rev signal would be good.  Cheers. Lee