#26Racing Posted December 24, 2016 Share Posted December 24, 2016 (edited) Hello Hello people may remember my build on the old site: http://old-skool-suzuki.proboards.com/thread/1675/home-brew-7-1216-turbo well, after holing a piston and it taking 18 months to rebuild due to outside forces, I'm back! I manged to get the Elivington to run the new engine in and was going ok until the rain came... I only had my stitches out of a hernia operation the day before so the running in at 160mph was probably as fast as I could have gone. I didn't realise how much weight I'd put on and couldn't get behind the screen So, on returning home I found that the motor was p1ssing oil out everywhere. A certain engineering company that did the rebore and ringing the barrels (in my mind) did a shit job, not listening to what Id asked for and it ended up being decked so I had to use 2x4mm base spacers... Best thing is, a new engine. I've learn't now that the wheel has been invented, and it's not bad, why re-invent it? Blandit motor Old motor meets new motor... Old motor coming down so the Busa rods can go in the Blandit t These were laugh to get out. .. Both engines down... The idea is I'll put Busa pistons back in the silver motor with the bandit rods, and the MTC turbo pistons will go back on the busa rods in the bandit motor. Not sure yet if the silver motor will be built as a na motor as the head is skimmed and ported and I haven't got a road bike so it'd be nice putting the 750 back on the road.... More later Thanks for looking Simon Edited December 24, 2016 by #26Racing 1 Quote Link to comment
#26Racing Posted December 24, 2016 Author Share Posted December 24, 2016 (edited) So, with the busa piston in the silver motor, with a suzuki stock base gasket we have this: Which, I think, with a copper gasket and the head with 30thou" skimmed off should give me a streetable motor. Am I right? Meanwhile, the bandit head was stripped and an order put in to Robinsons... Head cleaned up. It was very carboned, must be all that egr shit on the front of the motor... New seals, valves cleaned and lapped in All done Not all plain sailing though... Bloody crancase studs.. . After lots and lots of heat with a 25 nozzle on the oxy/acetyline I had to succumb and weld nuts onto the studs. Need to wait until the new year now as the kit is at my dads house and he's not well... See ya in a bit... Simon Edited December 24, 2016 by #26Racing formatting Quote Link to comment
MeanBean49 Posted December 24, 2016 Share Posted December 24, 2016 Awesome. You will get there mate. At least you managed to get out on it :-) Im just building my new motor now. Hopefully be good for over 300bhp Happy to help you out where i can too :-) 1 Quote Link to comment
#26Racing Posted December 26, 2016 Author Share Posted December 26, 2016 Hmmm, 2nd attempt as I dropped a photo in the "upload images" box and it missed, opened up a new page and lost 20 mins worth of typing and pics... This is far shorter.... So, was going to put the motor into this: Old ET chassis, got a Hayabusa rear wheel for it which is away at SF Services for new spacers to match the 20mm axle. Started trying to align the motor: Went for the alternative laminate flooring lining up method .. As I'd already put the old GSXR back to a 750 wheelbase: Wasn't happy with the forks as I'd previously had them powder coated and even though I was super careful they were just too thick to go into the yokes without scratching. It always annoyed me and after reading a post about some evil paint stripper, I removed the forks, stripped them, polished with 800, 1000, 1500 and finally precariously balanced polisher... Also took a punt at a CNC fuel cap from China. £13.80 delivered. Wasn't expecting much, but to be honest, it's spot-on! That's it for now, need to sort out more photos as once again my Iphone has decided not to talk to my lappy so can't transfer pics.. Simon Quote Link to comment
#26Racing Posted December 26, 2016 Author Share Posted December 26, 2016 So, things have changed a bit. I looked at the costs of putting the superstreet chassis back into service and decided that it's not worth it on this occasion. I'm going to build the new turbo motor back into the 750 chassis while I look around for an 1100K/L chassis and make another less dedicated dragbike. As I haven't got enough posts to see the "For Sale" bit I'm looking on Eblag but holding off in case any OSS'r has a frame, mounts and 1100K yokes for sale. Also, I'm struggling to find info as to whether the GSXR400 tank fits on the slingy frame, or the difficulty of making a later bandit tank fit. I want to chop the sup frame off anyway. Any ideas/info will be much appreciated... Simon Quote Link to comment
#26Racing Posted December 26, 2016 Author Share Posted December 26, 2016 (edited) Hello again, They say a pictures tells a million words. Well, not quiet... But, I've remounted the Walbro 300lp/h pump to a better place, drilled and tapped the fittings on the boost controlled fuel regulator so now I have a 4mm barb for the sensor tube, a 10mm I/D return (and a smoothed-off casting inside, the fuel in is also a true 8mm I/D pipe so hopefully I shouldn't have any probs with fuel flow . I've also sourced a racing wiring loom diagram that I will slightly modify as I'll be still running the alternator and charging system, although I'm struggling to find the improved charging mod from the old site... Think this time I'll look towards a Ignatec CDI as I'll have greater control over retarding the spark and rev-limit than I have now as I'm still using the 750L's 13,000 rpm CDI and it's always on the back of mind missing a gear... Simon Edited December 26, 2016 by #26Racing formatting Quote Link to comment
Captain Chaos Posted December 26, 2016 Share Posted December 26, 2016 charging system mod: http://oldskoolsuzuki.info/archives/400 2 Quote Link to comment
MrS819 Posted December 27, 2016 Share Posted December 27, 2016 Do like the new frame set up. Look forward to seeing it finished. One question on older post. How did you clean up your combustion chambers, what did you use? Ta Quote Link to comment
#26Racing Posted December 27, 2016 Author Share Posted December 27, 2016 (edited) 2 hours ago, MrS819 said: Do like the new frame set up. Look forward to seeing it finished. One question on older post. How did you clean up your combustion chambers, what did you use? Ta I 'm not using that chassis now as it's a bit too dedicated to what I need. I'd like something based more on stock than that long and low. just used a small wire wheel on the end of the drill. Took quite a while to get off, especially in the inlet ports. For the valves I just used emery cloth with the valve in the bench drill Edited December 27, 2016 by #26Racing Added more info Quote Link to comment
MrS819 Posted December 27, 2016 Share Posted December 27, 2016 Thanks for the information! Quote Link to comment
kiwi Posted December 31, 2016 Share Posted December 31, 2016 I have from a good source for cleaner valve faces and cylinder heads just use http://www.Eblag.co.uk/itm/MPM-Motor-Engine-Cleaner-Aerosol-400ml-Removes-Grease-Oil-Tar-/251610204391?hash=item3a952308e7:g:4dcAAOSwq7JT7K2E shit hot and when left on for a few mins quick rub with fingers and carbon just falls off. Quote Link to comment
Diebythereaper Posted February 23, 2017 Share Posted February 23, 2017 Great to see us all coming back on here, onwards and upwards for 2017 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.