-
Posts
3,034 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by CockneyRick
-
-
TA2530Z for the swingarm, but only thing close i think, is 32906 for the yokes? Anybody know if there available or even the proper 30-47-15?
-
Stuck it in here as i'm putting the USD SRAD yokes into the GSXR750G frame.
So can anyone tell me the bearing sizes for them both, & also the swingarm pivot ones for the 750G too?
-
18 hours ago, Swirl said:
think Nick C Hotrod has a couple of slabbies, lives up the Wirral from me, kill 2 birds with one stone, go and take some templates
Yea i know Nick well, but don't need any now as Cosmo had a shit load of copies he gave me ;)
So when's good to pop over?
-
Cos i don't have a template for them!
-
Lot of parts are interchangeable, but just as many are not! I need a set of engine mounts (6 off) & can't find any over here in UK, so if you wanna part with a set
-
yea, had a look on eblag & thought they looked 90mm, plus i'm so used to oil cooled i stuck this in wrong section!
-
-
So the SRAD uses the 65mm fitting, what other Suzuki's are 65mm too?
-
Jaydee, now i can see & remember how it mounts! As said been over 10+ yrs since i messed with a Slabby!
-
1
-
-
-
-
13 hours ago, Blue said:
Fit any forks & push them up through the yolks. Got gsxr750 k5 in mine
No shit! I want shortest so i don't have big tubes sticking above the top yoke, it's not for street so will be as low as you can go!
-
1
-
-
Don't go for CBR, not only are they Honka, they're too soft IMHO.
-
1
-
-
-
Must be my eyes but it don't look like it will? have too look at mine to confirm ;-)
-
Cheers matey, i'll figure best/lightest/shortest way to go when they're up here ;-)
-
Check you seated the diaphragm rubbers in the groove on top of carb, as it may have pinched too. Will cause same problem.
-
7 hours ago, Gpz1100_Convert said:
I do have a set of RWU zx9r forks here and a set of zzr1100 ones. both are lighter than USD and shorter. ZZR are free if you want them although you pay post bud. Cheap is the key!
I'd try shorter please, you can give em Cosmo as he still has all the bits at present. If i don't use em i'll let you have em back matey ;)
-
2
-
-
3 hours ago, Dezza said:
Just wondering, but why the shortest USD forks? Usually when a RWU bike is fitted with USD the aim is to fit long USD forks to maintain ground clearance and stability.
On a drag bike???
-
On a drag bike i doubt that will be a problem!
Thanks for offer on ZX6R front end, but might as well stick with the SRAD forks rather than spend more money.
-
1
-
-
Cheers for that, will look in to one once all the parts arrive.
-
Got an Srad forks, so u recommend sticking with that? If so, just need yokes, bearing size & some clip ons. Any chance?
-
Back after a break, & straight in with questions. First up, can anyone tell me the shortest forks in the USD range? I think poss RGV, but looking at cheaper & to fit a Slabby 750 frame. Oh & the matching yoke that'll fit with minimal fuckeroonery!
-
Be even better if u could cut out the inserts for a vented look
Oil & WC bearing sizes?
in Oil Cooled
Posted
Found one that size on Eblag for £11, looks like that's the way to go with spacers![;) ;)](https://oldskoolsuzuki.info/forums/uploads/monthly_2015_05/wink.png.2eec1a72c3be452ce1e041e23b233254.png)