69chris

is it going to be a project bike or a doner for your zed project bud ??

when i did mine (gsxr) i was advised that i needed a return of at min 8mm id as not to restrict flow, being a shed scrounger i rummaged about in my junk and come up with this that screws into the fuel level sender hole ( i know you may not have this fitting in your tank) been good as gold, i can adjust fuel pressure right down to just about 0 on the gauge so i guess its not restrictive

just looking at that link, the engine in my K is a V711 but i dont think iv ever seen that on one of those lists ??

cheers guys, pinky marks the rough spot of sensor ??

hey guys, been chimping around on the gsxr, putting on some miles whilst ironing out a few bugs etc and i guess its long overdue to look at getting some sort of wideband to see whats actually going on in there anyone using the AEM X-series available on that site ?? good or bad ?? also, iv been advised that my stubby little exhaust pipe isnt going to be any good and ill need to add some length to that in order to get a proper reading, is there a min length needed ?? cheers

prob not remotely the same reason but we used to do a similar thing to old rover v8 engines, the spindles are hollow and used to get sludgy oil in them but are capped with a small core type plug, we used to knock out the plug, clean out the crud then cap the spindle with bolts

any oss going along ?? https://www.calnebikemeet.com/

iv got a 1000 K something on my 1100 K but the top bolt on shock mount has been spaced away from the frame for clearance

could only find info on mk1 stuff..... dunno how different they can be/are but 4 turns out doesn't seem right lol

hey guys, mates just bought a mk2 1200 with less than 3000 miles on the clock - its been sat since it was a couple of years old and has never been mot'd lol !! just cleaning out the un-surprisingly grotty carbs and the mixture screws are currently varying between 1.5 to 4 turns out does anyone know what the standard setting should be ?? cheers

ooooo id love a kat !!!!!!!!!!! my 2 pennies worth, keep the red efe and kat

cheers for advice fellas, the new battery sorted the problem, still have the battery light on so going to hide it under a bit of tape.......outta sight, outta mind right and away back home it goes........ cheers all

whats the best way of mounting an aftermarket cooler on a slingy ? mines just cracked somewhere and is now merrily dripping oil on the floor !!!! i vaguely recall reading something about rubber mounting them, cant remember for sure....its entirely possible i may have dreamt it !!!!! anyhow, iv ordered a new cooler but has anyone tried using something like those little exhaust mounting rubbers, the round/barrel shapped ones with an m8 stud on each end, to mount the cooler bracket to the frame ??

tbh i didnt even put the test light/meter on it, just pulled it off and tried to forget about it even being there once get new battery fitted ill mess with it some more cheers guys

i do actually have a .........spare wire near the reg/rec area, its a blue/green with with a small resistor / diode looking thing on the end and no apparent place for it to go to, in my defence i didnt strip the bike so have no idea what its for/where it goes lol !!!!!

if you happen to pass a snotty ole blue slingy at side of the road, most likely either on fire or surrounded by bits , please dont stop to point/laugh/take the piss....it'l just be another day in the life of being a Chris

any other Wiltshire based oss folk doing to be going along on Monday ?? http://www.avebury-club.co.uk/event/stone-circle-classic-and-custom-ride-in-bike-show-2019/

thanks guys, new battery should be here tomorrow, just got impatient and wanted to hear it running again

we got the EF running again today , apart from a few little niggles it seems to be running well, but it appears to be overcharging somewhat, i have 14(ish) volts at 1500rpm then 15.5v at around 3000rpm the battery warning light on dash is also lit, the bike already has an aftermarket reg'rec unit (electrix iirc), the bikes battery is fucked so we had it starting of a jump pack , then running on its own - would/could a weak battery case those symptoms ?? cheers

for a slingy, has anyone found one off another bike that'l bolt on and stand the bike a bit more up-right or is it a case of getting the stock one lengthened ?? cheers

found this......wont help much i know but.............. 37 Suzuki XN-85 D "Turbo" (83) 37 Suzuki GS-500 EK/EL/EM/EN/EP/ER/ES/ET (89-96) 37 Suzuki GS-500 EV/EW/EX/EY (97-00) 37 Suzuki GS-550 LD/LF (83, 85) 37 Suzuki GS-550 ED/ESD/ES3/ ESE/ EF/ESF/ESG (83-86) 37 Suzuki GS-650 MD "Katana" (83) 37 Suzuki GS-700 EF/ESF (85) 37 Suzuki VS-700 GLFG/GLEFG/ GLFH/GLEFH "Intruder" (85-87) 37 Suzuki VS-700 GLPG/GLEPG/ GLPH/GLEPH "Intruder" (85-87) 37 Suzuki GS-750 ED/ESD (83) 37 Suzuki GS-750 LN (79) 37 Suzuki GS-750 SD "Katana" (83) 37 Suzuki GS-850 GN/GT/GX/GZ (79-82) 37 Suzuki GS-850 GD (83) 37 Suzuki GS-1000 C/EC/N/EN/ET (78-80) 37 Suzuki GS-1000GT/GLT/GX/GLX (80-81) 37 Suzuki GS-1100 ET/EX/EZ (80-82) 37 Suzuki GS-1100 ED/ESD (83) 37 Suzuki GS-1100 GZ/GLZ (82) 37 Suzuki GS-1100 LT (80) 37 Suzuki GS-1150 ES3/ESE/EF/ESF/EF2/EG/ESG (83-86)

would it not be easier to fit an external wastegate bud ???

cheers guys, cant find any actual 'together' pics but looks like a normal remote res master ..... in bits..... just couldn't find a list to what bikes used what bore size in order to get a seal kit (cheers Lachie04 ) annoying as fuck !! was fine on Monday, yesterday went to pull in the lever whilst moving bike out of shed and it didn't spring back out as usual.....was sort of loose and floppy , stripped the cylinder down expecting to find corrosion or other general grot and it was clean as a whistle do the seals suddenly just swell up and get sticky ?? fluid was changed only about a month ago and all has been fine until yesterday.........

hi guys, my brake master cylinder is shot, problem is i dont know what its off and all the repair kits listed on that site only show whats bikes they are for, not any sizes, typically iv no idea what mine come off originally !!!! its a Nissin 14mm remote res master - anyone know what used those so i can source a seal kit ? i do also have another Nissin remote resni could use, but in 5/8th's, again, any clues to origin so i can obtain a seal kit ? cheers all