iamhiding

Alriiiighty, can anyone help out with some oss wisdom trying to find the length for the rear wheel middle bearing spacer 64731 40C00 000 For the 5.5” gsxr 750 / 1100 W / mk1 blandtit 12 / non abs mk2 blandtit 12 / rf900 / slingy 11 / probably a few more bikes. Cant find the length using the usual means of parts catalogues / fiches. Scoured a few forums too. a measurement from outer bearing edge to outer bearing edge would do but needs to be precise. Can’t currently get access with this covid nonsense to my 11 or I’d pull it apart to check. Massively appreciate any input, cheeeeeers.

finally! a box of genuine suzuki goodies fresh from japan... almost £700s worth, glad i wasn't paying for it. mirrors, two main front brackets, two side brackets and their respective plastic plugs. the cost is criminal. must say i'm a little disappointed with the quality of the main brackets, expected a little better than that, i'll grab a pic for next time but they're questionably finished in places.

actually i lie, found pics of the different internals. fairly self explanatory.

long time no update! couple of things. obviously sorted the front sprocket nut issue, the inner mudguard rubbing, the waterpump gasket and flushed the cooling system, seems to be running much cooler now , not that it was boiling up before. havent dealt with the disk bobbins failing, thats a winter job. clutch slave is sticking i think, all travel is basically down at the bar. balanced the carbs, cleaned and re-oiled the k&n. stole the cruddy looking disk bolts from the 11, cleaned and painted them for the gs project and replaced the 11s with some nice shiny titanium bolts. got some rear paddock bobbins on. got the new nosecone, paint work is obviously a winter (or next summer) job. need to see about getting oem (or very good aftermarket) decals. the brackets etc have finally turned up, pick them up from the garage tomorrow. had a thought about the chain rubbing issue, it could be down to the swingarm being at a different angle, its something i meant to measure but completely forgot to. it would explain the chain rubbing on the frame below and also on top to the rear of the chain guide. i do have a set of shorter dogbones but im not sure if that would help the situation lifting the rear or i have the 750 wp suspension knuckle still and i cant remember if it was slightly different or not. the exhaust has been rebuilt two or three times now, rattled itself apart, took the packing out... rattled itself apart, put it back in haha. rattled itself apart, ditched the restrictive remus outlet in lieu of a spare yoshi one (almost double the diameter) and reworked the internals with larger bore scorpion parts. certainly made a difference as did re-drillling the holes and using larger and better quality rivets. lost the pics of different internals unfortunately. // its been a summer of power wheelies, hanging off, tormenting much newer bikes haha just using it like an auld' gsxr should be used. it might be oldskool, it might be heavy, useless in town, handle like a pig, a water boiler even but the gsxr 1100, what a fucking machine! never a dull moment. still baffles me that anything half as mental is road legal i've got 4 days of tax left and the 11 will be cleaned, protected & stored away in a friends heated garage for winter for the next lot of sorting / modding / restoration. might even give next season a miss and use the time to totally get it up to scratch. a bit undecided really. back to full time on the angry wee gs500 rat tracker for winter soon.

well, b12 lock tab washer and the waterpump gasket are here and i've even found a bolt that seems to match. thats on the cards for tomorrow amongst a hundred other things and i should have a second set of hands to diagnose why the chains catching on the frame. the RHS disk which was spleet new when i got the bike with only a couple thousand mile on it now's bobbins have come slack, far too much rotational play, worst ive seen. going to try the ball peen hammer tappity tap to tighten things up and if not then its a blackshadow bobbin kit. rivets on the exhaust have also worked themselves slack so that will need rebuilt as well, toying with the idea of gutting some packing out, a bad idea i know . also just secured a new nosecone for the second set at reasonable cost. its from the 750 wn but some oss wizards have vouched for them being the same part hopefully get round to mocking up some brackets to fit blue spots onto wp 750 forks for the mental wee gs5 winter hack as well if the weekend allows.

looks like a tidy one meant to be an incredibly underrated bike

thought that was the case, thanks nightrider! massively appreciated! oh and Almostthere

Sure I've read that the 750 and 1100 wp fairings are interchangable, any truth to this or does anyone know better? I know the tails are slightly different and they have different grab handles. Mainly it's the nosecone I'm curious about, last 3 digits of the parts number are different but that doesn't account for much does it. visually I can't spot any differences looking at pics online. So... Em yeah... Anyone know? tah!

noticed a couple of things. firstly the sprocket nut keeps coming lose when torqued to spec, even when loctighted. the sprocket bolt on the end of the shaft sheared on me which is a pain in the arse... wasnt even going to town on it, nothing i had lying around is the right thread pitch either. so i've ordered up a bandit 12 lock tab washer to see if its enough to stop the nut spinning and if not it'll be a rather expensive new nut needed. sourcing a new bolt for the end as well. but look at the unusual wear on the inside of the chain! recently solved a similar mystery on a friends bike, turned out to be fouling on a nut on the inside of the footpeg on his. spot where mines is wearing on the frame... no idea why its doing that, perhaps the different swingarm angle? chain tension? need to look in to it further. also found the inner mudguard to be rubbing on the swingarm leaving a wear spot. something else to be dealt with. and finally a leaky water pump gasket haha oh the joys of owning and modifying old bikes bike isn't half desperate for a clean, think thats next on the cards once parts turn up etc.

christ they're tidy! chances are i would've snaffled them up if i hadn't already wound up with that red second set, well spotted . just going to play the waiting game till i can piece together the original set somewhat cost effectively i think then get indecisive with what i'm doing with the paintwork. well i finally heard back from the garage about the cost of parts but he's given me a quote for the lot, not a breakdown like i asked... ahwell, still waiting on getting a breakdown of cost. but yeah about 1200 odd to replace everything damaged minus the left panel as they're no longer available. call it 1800 like i had predicted before paint. crazy to think it was only knocked of its stand. // got stuck into it the other night. nothing particularly interesting just rebuild kits on the front brake & clutch master cylinders, pulled the callipers apart again as they were still sticking and took a dremel and wire wheel to the seal area finishing it off with a pick to make sure the hidden bits were clean, fresh seals, nipples, galfer 1375 pads and stainless bolts. no fucking around this time and they no longer seem to stick. using the bearing puller makes the job sooooo easy off the bike, unbelievable and all bar one piston needed the slide hammer for it to shift, the rest slid out no bother with something gripping the inside.

tell me about it crashtester! within 10 miles of my doorstep as well, cant believe it. quite like the red slabby/slingy and the yoshi schemes but never really rated any of the colours the 11 w came in but the red really is the nicest by far and it really is much better looking in person (mine not being a great example haha). i think there was a couple of (questionably) cool 750 w schemes the 11 never came in, ie pink/baby blue and yellow, odd, total shell suit colours but surprisingly smart... if you dont mind being seen on a pink bike that is

done 113miles on the old tank before i switched everything over and i doubt 100ml was left from a full tank... damn these things are thirsty when you get them going.

bit of a weird turn of events here... a continuation of bad luck with the 11. some colossal fuckwit whose bike we just got running and someone i still (dubiously) consider a close friend reversed his car into the 11 and knocked it off its stand yep quarter of a ton of bike put on its side. scratched fairing obviously, bent top fairing/mirror bracket, probably bent lower fairing/headlight bracket, left side bracket crushed, ride side bracket bent out the way, mounting points torn out of headlight and cracked in places, left hand panel broken on inside mounting point, basically shunted the whole fairing across to the right. i've not really taken any pictures because its pretty heartbreaking to look at even though it looks incredibly minor. estimated cost of NOS parts if available: £1200 worth of plastic, yep for a nosecone and left panel. £550-600 worth of brackets + prep & full respray. should really have been an insurance job considering the value of the bike and availability of parts but circumstance dictated otherwise. he is however covering the cost of repairs and not dodging me so credit where credit is due but its not exactly the considerable payout im due and i have to take my own time to source parts and sorted. // anyway by pure chance a friend of a friend was selling his old fairings and a few bits and pieces for reasonable money locally and now i've got a very red looking 11, not really a red bike kind of guy but its pretty original and smart, was never all that fond of the relentless rep paintwork to be fair. bodyworks in worse condition than my old fairings but atleast its not broken, right. still need to source brackets, waiting on a quote from a local classics garage for parts and it'll be taken from there. going to replace the broken bits on the other set when they pop up for reasonable money and get the set painted and stickered in one of the original colourways i think. // what a pain in the arse... and of course the last bits i was waiting for to do the brakes etc turned up the following day but its straight(ish) and plenty rideable not to mention everyone knows red goes faster. degreased the engine area down whilst it was all apart and sprayed it all with ptfe, its absolutely gleaming under those fairings.

thanks skunk lots more to come.

carbon yoke cover. usually i hate faux carbon but its subtle enough and covers up the key scratches without any effort on my part. the front brakes have been sticky since i got the thing, figured it was about time to deal with them. thought i try rebuild them without replacing seals as they aren't cheap on 6-pots. tried to get all the pistons moving under hydraulic force prior to removing them, y'know as you do. bar 2 i couldn't get moving with the other pistons locked up to stop movement... i never had that before. so callipers off and even using 120psi of air through the bleed nipple i couldn't get them moving which is just absurd. soaked the seals in penetrating oil, filled the calliper with the stuff as well. with that in mind the picture was taken before pistons were polished up and the callipers cleaned. obviously it was just a build up of shit behind the seals but for the callipers to look so presentable and be that seized is really odd. dealt with plenty of callipers being awkward but thats hands down the worst. split the callipers, re-soaked the seals and got an internal bearing puller / slide hammer on the bastards. used inner tube to protect the contact point on the piston and ensured it was pushed fully into the base where it would be least likely to deform the piston, didnt need to tighten it up very much to get a grip so ive got no concerns on that front. clamped in a vice, couple of wee taps to get it moving, another squoosh of oil, tapped it back in to get everything slidey and then a couple of taps and is popped out effortlessly. perhaps a bit excessive but youve got to work with what youve got dont you and it might just be my preferred method of dealing with brake pistons now. absolutely effortless, even with pistons that are as seized as they were. =D slips into the piston so you don't need to worry about marring the outer surface, just another way of doing it i guess. the seals were messy but salvageable, seal area heavily corroded. cleaned them out, machine polished the pistons even though they were perfect, slapped them back together, bled them in... annnnnd not as bad but still sticking. thinking maybe i missed some corrosion so they'll be getting pulled again, cleaned... seals replaced and hopefully that does it. fresh galfer HH 1375 pads and the master cylinder rubber is perished on both brake and clutch side so both will be rebuilt. just waiting for the brake master to arrive. certainly a bit more than i wanted to spend doing it but at least it'll be right. stainless bolts sitting for the brakes as well.