Screwriverracing
-
Posts
395 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by Screwriverracing
-
-
Bad earth, high resistance, means more load , load = heat.
Cheers SRR
-
1
-
-
-
Here's one from earlier.
-
Look what happened to the classic Suzuki Katana, gutted.
-
And here's mine
Cheers SRR
-
2
-
-
Still struggling with the throttle bodies, so I pinched Marco's idea and used a ratchet strap.
worked brilliantly, put some tension on then wiggled them and they have all seated nicely.
The proof
Thanks Marco.
Cheers SRR
-
1
-
-
Right, just spent an hour in the garage with a big wooden stick, and have nearly got the bodies back on. Having trouble with no2 so will have another go tomorrow with 2 sticks. Can get 3 and 4 in easily , just 1 and 2 being a pain..
And Marco not sure about the Donnington day, have a lot going on at the moment.
Cheers SRR
-
On 13/04/2017 at 3:05 PM, bruteforce said:
Does it run yet
Very pretty plenum btw!
And just in case you haven't noticed there are bell mouths on the back of the throttle bodies that the plenum is built round.
And no it doesn't run yet, still haven't got the bodies back on, family life and work have been holding me up.
Cheers SRR
-
4 hours ago, colinworth79 said:
what are the TB's off ? Not seen ones with 2 injectors in .
There Jenvey.
Cheers SRR
-
Got the manifold back into position, now just need to get the throttle bodies back in the rubbers.
Cheers SRR
-
3
-
-
Put the injectors back in, now just have to refit them onto the bike.
-
5
-
-
They were tested at 3 bar, spray pattern wasn't to hot, but cleaning has sorted that.
I will try and get it running again over the weekend and see if it still smokes.
Cheers SRR
-
Injectors have been checked and cleaned, they said they weren't leaking and were not to bad.
So could excess fuel pressure be causing them to leak?
Cheers SRR
-
I have taken the injectors to a local injection place, they are going to check them and clean them and replace the o rings etc, ,cost is £15 each.
, no cost if they are not repairable.
Not to bad and I can pick them up without any postage costs.
Cheers SRR
-
Fired it up today, took ages. Would fire then die. Plugs were really wet, so toook them out heated them up and tried aagain, same problem.
Next I changed the phasing on the injectors, and it fired up and ran, even ticked over, but was smoking badly.
Even fever it hard enough for the BOV to open, nearly s--t myself.
Stripped out the plenum and found some of the injectors leaking.
So I have decided to remove the injectors and get them cleaned.
Where should I take them, and how much should it cost to have 8 injectors cleaned?
Cheers SRR
-
1
-
-
Nice job, a shame bruteforce didn't see this before putting his on.
Cheers SRR
-
1
-
-
-
I have found another ecu manufacturer Eblag no 272423568938.
Have spoken to them, apparently there software came of the back of a Le Mans car( couldn't tell me which one) and said it should work no problem.
Benefits its are they are localism,( might have to ask fatblokeonbandit to do a drive by)
Good price at £595 including lead and basic harness.
Problems, they have never done a bike.
What do you think?
Cheers SRR
-
Been talking to a couple of ecu makers, they suggested changing the timing wheel and if the settings can be altered to try it on the current ecu.
So I am going to try it, have contacted RACETECH to see if it is possible to change the pickup type in the program.
was wondering if this might help with the problem of starting it sometimes when it makes a loud cracking noise and the engine seems to go backwards, not good for the starter clutch.
Cheers SRR
-
Another option is to take the generator and starter clutch off, bump start it and see if that makes any difference.
If it's a sort of rumbling could be one of the crank roller cages breaking up.
Cheers SRR
-
26 minutes ago, luke2152 said:
Well i pulled my barrels off today ready to get them bored. will i need a ring compressor to get them back on or will the chamfered bit in the bottom compress the rings ok.
No necessarily, you can do it by hand, get to pistons up, put barrels over while compressing rings by hand, then turn engine over slowly to bring the other two pistons up and ease in by hand. Probably much easier with compressors, but I have allways done it by hand.
Cheers SRR
-
1
-
-
For those who are interested here is a pic of the inside of one of my RACETECH ecu's
Cheers SRR
-
8 hours ago, busa ash said:
stunning just that ......looks amazing is it going non suzuki 1400 or kwak 1400 ?
Going kwackers.
Cheers SRR
-
1
-
-
Yes
-
2
-
Hot earth!
in Oil Cooled
Posted
So as said bad connection = high resistance = load=HEAT.
simple ohms law.
cheers SRR