Gixxer77 Posted June 5, 2018 Posted June 5, 2018 (edited) I'm about to buy a brand new set of RS smoothbores for my 91 gsxr750 Before I do I'd like to ask for any recommendations on size/type and any peripheral products I may need to get this job done like throttle cables, intake manifold rubbers/clamps, etc etc. Can I run them straight out of the box? or would I have to tune them - replace main jets adjust needle height etc? Thanks in advance! Edited June 5, 2018 by Gixxer77 incorrect details Quote
riversbikes Posted June 5, 2018 Posted June 5, 2018 You will need push-pull throttles for sure. I used an off the shelf set from Motion Pro that worked perfectly. Set the floats at 17mm (they are all out), and follow the jetting guide included the manual. It's a good baseline. Quote
Gixxer77 Posted June 5, 2018 Author Posted June 5, 2018 (edited) I've been informed that Mikuni distributors must advise on dual throttle cables however it's not necessary. Also I have been informed that I will not have to re-jet them, just bolt them on and hang on! Strange that it's necessary to set float heights before use... Anyway, order placed, awaiting delivery. Edited June 5, 2018 by Gixxer77 incorrect details Quote
Gammaboy Posted June 5, 2018 Posted June 5, 2018 12 minutes ago, Gixxer77 said: I've been informed that Mikuni distributors must advise on dual throttle cables however it's not necessary. Quite frankly, Fuck that. 3 Quote
Gixxer77 Posted June 5, 2018 Author Posted June 5, 2018 Fuck what exactly Gammaboy? not using dual cables? Did you want to contribute a little more context around your response? because that's about as useless as tits on a bull Quote
Mole28 Posted June 5, 2018 Posted June 5, 2018 If you run a single cable on them you run the risk of the carbs jamming wide open, especially in the rain. Quote
MeanBean49 Posted June 5, 2018 Posted June 5, 2018 Personally I would invest in some dyno to to get them setup properly. Never know a set of aftermarket carbs work perfectly straight out of the box. Ive always run a single throttle cable with no problems at all. Quote
Gixxer77 Posted June 5, 2018 Author Posted June 5, 2018 17 minutes ago, MeanBean49 said: Personally I would invest in some dyno to to get them setup properly. Never know a set of aftermarket carbs work perfectly straight out of the box. Ive always run a single throttle cable with no problems at all. Awesome, thanks for the useful feedback! Quote
Gammaboy Posted June 5, 2018 Posted June 5, 2018 Fuck running a single cable and running the risk of the carbs hanging open on the way into a corner. I'm sure some people do it, but it's not something I'd risk. 1 Quote
Solcambs Posted June 8, 2018 Posted June 8, 2018 On 6/5/2018 at 11:34 PM, Gammaboy said: Fuck running a single cable and running the risk of the carbs hanging open on the way into a corner. I'm sure some people do it, but it's not something I'd risk. I'm with you on that - Probably fine when knew ... but more likely as carbs get older - especially with Mikuni as they do not have slide bearings. besides an universal cable and push pull throttle kit isn't that expensive in the grand scheme of things. 1 Quote
Gammaboy Posted June 11, 2018 Posted June 11, 2018 On 6/9/2018 at 12:48 AM, Solcambs said: I'm with you on that - Probably fine when knew ... but more likely as carbs get older - especially with Mikuni as they do not have slide bearings. besides an universal cable and push pull throttle kit isn't that expensive in the grand scheme of things. Cheaper than Hospital bills! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.