smudge

Thanks guys, that's really good to know , much appreciated.

Hi lads, okay I'm gonna bite the bullet and pick up a low mileage bandit 12 and swap the motors , can I take it as gospel that all oil cooled bandit 12 engines are a straight swap into a slabby frame? Any years I should look for or avoid? Any and all advice appreciated.

Totally agree.

Thanks, yea I was thinking the same thing about the b12 motor , possibly picking up a low mileage bandit 12 in good order, swap the motor and sell the rest, my previous bike was a b12 I loved the motor but wasn't keen on the rest of it, I'm not sure if I have the skills/experience for a bottom end rebuild, thanks for the reply, appreciated

Thanks for the reply, yea this is what I was thinking , I knew the compression wasn't great and figured it would need at the least new piston rings , oil pressure was my big concern, hard to tell without a temperature gauge when the engine is at 60 degrees, but it seems way hotter than that, even when I'm out and about if i stop moving for more than 5 minutes smoke starts coming the engine breather. As far as ignition timing I fitted a dyna 2000 ignition system and was super careful when fitting it .

Hi guys, so been up on the road on my recently done slabside 1100 fighter , the bike was put together from bits and pieces so the plan was to get some miles on it and test what's working and what's not , every thing seemed to be going okay apart from a few tweaks here and there , really wanted to test the engine as I was planning on getting it bored out over the winter, it's an original 1052 engine with dyna200 ignition, stage3 jets and pod filters, I noticed there is smoke coming from the engine breather with that smell of burning oil when it gets hot and it seems to be hot all the time! It seems to be going through a lot of oil ( over a litter in 800 miles) but it doesn't seem to be burning it in the cylinders , the engine runs and sounds okay but not as fast as I thought it should be so I did a compression test on it and it wasn't great ( around 100psi across the board if the cheep Chinese compression tester was reading right before it fell to pieces!) Was planning on boring it out anyway so wasn't to worried about that but figured I'd do an oil pressure test just to be sure , when the engine is warming up it reeds at about the minimum 40ish psi but when it gets hot it drops to between 15 to 20psi , I thought this seemed a bit low so I dropped the sump out and checked the oil pressure regulator and relief valve and they seem fine, repeated the test with fresh oil and got the same results, would really appreciate any advice here as this level of spannering is pretty new to me! Are these oil pressure readings on the low side? Replace oil pump? Combined with the low compression test is this indicating a worn/ knackered Engine? As usual any and all advice really appreciated

Thanks, really appreciated, yea I got most of the fancy stuff from motogadget , they are a bit expensive but the quality is pretty dam good, there are cheaper alternatives , might be just as good, thanks again.

Cheers Dave, heard it's like trying to paint your hallway through the letter box , so true!

Thanks very much. All the welding, fabrication and electrics was done by myself, the only thing I paid out for was anything CNC billet, swingarm and paint , I totally underestimated the work that goes into these projects! Have a whole new respect for the guys on this forum! Cheers , really appreciated. Not sure if anyone is interested in this but I used a motogadget m lock , it's a sensor and RFID chip that you use instead of a key , people normally sew the RFID chip into their gloves or jacket sleeve so you don't have to Cary key's around but I would probably loose them anyway, so I made a ring out of a stainless steel nut and epoxy'd the chip into it. It's well handy.

Cheers Dave, this was my first time wiring a bike from scratch so I was learning as I went along! I used a motogadget m unit which I would definitely recommend, the only thing I don't like about it is the side stand switch only cuts power to the starter not the ignition so I spliced in the relay and diode from the original loom, ( definitely don't recommend trying to go round a left hand bend with the side stand down!!!) Hardest part was wiring the switch gear through the bars! Thanks again, appreciated.

Cheers, this was my first "proper" bike build so thought simple done well would be better than complicated done badly! A lot of the work you can't see!

Cheers guys, appreciated.

Finally on the road with my slabside streetfighter ( Jesus only took 6 years!!!) Big thanks to everyone on Oss who took the time to answer my questions and offer advice, really appreciated. Also big thanks to streetfighter magazine for all the beautiful bikes and boobs before the internet.

Hi, big thanks for the recommendation , just got my bolts from Ralph today, he done a superb job, I would definitely recommend him as well, cheers, appreciated.

I wrap it tight with masking tape, and then carefully cut around it (not through it in one go) with a grinder with a 1 mm micro disk, then use a socket to hold the fitting and push n twist it on , I don't leave the tape on , hardest part is not marking the fittings . I also blow it out after to make sure there's no bits left in it.