Brucekirk
-
Posts
15 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Posts posted by Brucekirk
-
-
I did a draw test on starter and its putting out fine...I took new battery back got it replaced its turning over fine now had a dead cell under cranking it would drop below 9volts seems fine now.
-
On 11/11/2017 at 3:28 PM, wraith said:
Looking nice, as to the cranking slow, try a different starter or new brushes also try a extra earth wire (coming from one of the two 6mm bolts that hold the starter motor in place and run it to the frame/battery)
Battery is brand new but I did a load test..sit at 12+,running its 13+ but it drops down to 9volts under starting must be a shite battrey,wiring harness is brand new i built it and double ground most things from experience lol but never thought aboot re-grounding starter good idea.but I think I need ANOTHER battrey good thing these Exide batteries have warrnties.fires up two cranks but sometimes its like battrey is low
-
Just now, Brucekirk said:
Nice...I thought aboot grafting a bandit swing arm to mine but don't think they be much of a difference between the two as in rear tire size in looking for a wider tire for the back I'm replacing it next month would like a fatter rear any suggestions would be gooder,and id love to get some gsxr forks and a allballz bearings kit.
And were does ur oil cooler connect by the way
-
12 hours ago, CockneyRick said:
Nice...I thought aboot grafting a bandit swing arm to mine but don't think they be much of a difference between the two as in rear tire size in looking for a wider tire for the back I'm replacing it next month would like a fatter rear any suggestions would be gooder,and id love to get some gsxr forks and a allballz bearings kit.
-
On 11/10/2017 at 5:52 AM, Blubber said:
It's got a nice burble to it
Straight pipe lol
-
-
-
3 minutes ago, Dorkburger said:
If your replacing the tail section, hold on to, or sell that chrome trim piece. They apparently disppear over the years and stock type resto guys are often on the lookout for them and the clips to hold them on.
Im just going to build or buy a better seat flatter one but matches back cap
-
On 11/9/2017 at 8:57 PM, Fjbj40 said:
If it's hard to start something is not right!
Cranks slow sometimes but fires right up no problems
-
On 11/10/2017 at 2:45 PM, wraith said:
Welcome to OSS
Yes their is something wrong there GS1000 start very well, my GS1000 Start's first push of the button, apart from when its -0 or below, which I don't think you will get that sort of temperature in Texas
Two cranks it start fine warms up just putting gloves on but some times I gotta jump it a little and battery is brand new just cranks slow sometimes
-
11 hours ago, CockneyRick said:
True oe usually better I try not to buy anything new if I can help it only cables tires drive chain but there usually shit quality.
-
On 11/10/2017 at 5:52 AM, Blubber said:
It's got a nice burble to it
She's super fast pulls hard every gear all the way to 12k rpms and I ride her hard too
-
On 11/10/2017 at 4:26 AM, gs7_11 said:
I can't find your website.....I'm keen to have a look.
Hard starting? No, that's not a GS trait...you've still got a fault. Or two.
Hmm from cold these all are hard starting two cranks it fires up no problems stays running only takes putting on gloves for it to warm up to ride away.IV had 3 78-79-80 all pesky to start if left a few days.
-
Ground up restored 78gs1000??
Rebuild engine weisco big bore kit bottom end milling done by local shop but I did everything else in my shop kirkcustomcycles.com 4-1 headers were crushed underneath so I built new exhaust but the pipe was good so I reused it sound mean with straight pipes
Stripped painted entire bike just waiting to paint tank fully just not sure of tank color yet might just hydrodip tank carbon fiber??
Fully rewired bike built harness myself,,WISH THESE HAD KICKSTART tho lol.
Not sure if I want to café this bike kinda liking the stock look but seat looks like crap why I hvnt reapulsterd it yet not liking the shape but stuck with shape if I want to keep back cap and ninja pocket.I'm going to get a fearing for it for sure and replace bars not liking the beach cruiser bars at all.looking to swap forks out but not sure what style yet or at all.everything replaced or rebuilt still hard starting but guess that these Gs all 3 of mine were lol
1978 Gs1000
in Air Cooled
Posted
I did a draw test on starter and its putting out fine...I took new battery back got it replaced its turning over fine now had a dead cell under cranking it would drop below 9volts seems fine now.I'm replacing cables and building a ground strap for the starter