Jump to content

Service manuals


Bomber666

Recommended Posts

L O All, it’s been a while since my last post and I do try to be as independent as possible but I’ve just purchased a very clean and original 1990 slingshot and need to do a few small jobs so can someone please point me in the right direction for a gsxr1100L workshop manual download.. and also a 1999 Srad 750 manual or exploded drawing of the front end... I’m fitting 1999 GSXR 750 forks with a 1100 M wheel so need to see the spindle spacer, can’t find one anywhere.. I have the spindle and bearings but no spacer.. 

thanks in advance..XxX89434F49-E59D-4B1F-B48E-2822DF6D6625.thumb.jpeg.d56858c06b5c2da1c3f4d486ec135799.jpeg

83D5F962-61D8-49A7-9ABC-3AFEA8EF3E13.jpeg

Link to comment

I might be shouted down, but the 11M wheel in Srad ain't easy. Better off with the proper wheel tbh. 

If it's so you can run the speedo, then go back to Slingy forks. 

The Srad "spacer" is actually the nut that is gripped by the fork bottoms & screws onto the spindle with the spacer as part of it.

19181990_10155136310175733_1224858765_o.jpg

  • Like 1
Link to comment
11 hours ago, CockneyRick said:

I might be shouted down, but the 11M wheel in Srad ain't easy. Better off with the proper wheel tbh. 

If it's so you can run the speedo, then go back to Slingy forks. 

The Srad "spacer" is actually the nut that is gripped by the fork bottoms & screws onto the spindle with the spacer as part of it.

19181990_10155136310175733_1224858765_o.jpg

Thanks M8, I was beginning to regret the whole idea.. actually it was the inner wheel spacer between the bearings I was looping for.. 

I’ve still got all the stingy bits so might just go back to that idea.. I bought the Srad forks cos the stansions are a bit pitted on the slingy ones and thought it would be an easy swap not realising that I’d have to swap everything ..  just my luck.. cheers for the advice Pal..x

Edited by Bomber666
Link to comment

Yeah, has to be something for the inner race of the bearings to clamp to on the inside, or else the tendency will be for the inner race to turn along with the outer race / wheel.  The inner race should not turn around the spindle.  I see that as item 2 on the fiche too.

Edited by Crass
  • Like 2
Link to comment
40 minutes ago, Crass said:

Yeah, has to be something for the inner race of the bearings to clamp to on the inside, or else the tendency will be for the inner race to turn along with the outer race / wheel.  The inner race should not turn around the spindle.  I see that as item 2 on the fiche too.

Yeh i removed the bearings and spacer from the 1100M wheel cos the spindle for the SRAD forks is much thicker (pic) but now I’ve just realised that the speedo drive is too small as well.. That’ll probably be another £30.. bollox..!

another lesson learned.. 

F9D7D028-69D2-487D-8B37-243CBD187218.jpeg

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...