clivegto Posted November 19, 2025 Posted November 19, 2025 9 hours ago, Allspeeds said: There not mine there one of his customers but there not coated there new stations from Italy available in various nitrile finishes I’ve chose my colour and it ain’t black My money is on purple Quote
R1guy Posted November 19, 2025 Posted November 19, 2025 5 minutes ago, clivegto said: My money is on purple Where can one purchase these purple stanchions? Quote
Allspeeds Posted November 20, 2025 Author Posted November 20, 2025 I believe he brings them in fro Italy most of the stuff he uses if he doesn’t make it comes from overseas as it isn’t available here Quote
Allspeeds Posted December 2, 2025 Author Posted December 2, 2025 So today just tidying up I ended up going down a rabbit hole sorting what I had to assemble bottom end after Xmas opened cases that have been painted for a year I’ve been ordering offs and sods over summer genuine parts mainly seals and bearings I’m replacing everything I also bagged up and have dropped off all hardware for zinc plating so it’s ready soon be time to send that crank @imago the bits I had cericoated will be re done as the colour is different to the hard anodising finish mark with be making all my parts 3 Quote
Allspeeds Posted December 2, 2025 Author Posted December 2, 2025 And no I’m not using that 25 year old gaskets bye the set it was just in with the bits Quote
Allspeeds Posted December 2, 2025 Author Posted December 2, 2025 I might did dump plate and oil filter cover out for @Loudpipesto vapour for me il send it with barrels for correct colour change, il be using a complete EFE head I think so won’t be sending the top end Quote
Allspeeds Posted December 3, 2025 Author Posted December 3, 2025 New oil jets for cases…. Educate me Quote
Allspeeds Posted December 3, 2025 Author Posted December 3, 2025 Up rated oil pump ratio needed or not? Quote
Allspeeds Posted January 7 Author Posted January 7 Due to snow I’ve had abit of time today to dry build the Harris Et engine to work out what I have or haven’t as it was in total kit form I’ve had bags of bits zinc plated as they were in boxes using basic knowledge and help from @imagoive started to cobble an engine together 7 Quote
Allspeeds Posted January 7 Author Posted January 7 Next job I must send off the gearbox and selectors for super finish as well as get to the bottom of the clutch anomaly 1 Quote
Allspeeds Posted January 8 Author Posted January 8 Routing through boxes today what I thought was some old stock pistons as the Harris came with new 1168 pistons and fresh cylinders turns out to be some barley run IMO 1260 pistons 3 Quote
Allspeeds Posted January 8 Author Posted January 8 Marks been on he’s been making some bits past few weeks many of you will have seen his bits like this before but still nice 8 Quote
Allspeeds Posted January 9 Author Posted January 9 Few more bits done for the dry engine building today need to find a complete efe head now 7 Quote
R1guy Posted January 9 Posted January 9 10 minutes ago, Allspeeds said: Few more bits done for the dry engine building today need to find a complete efe head now I believe Quist has an Efe head for sale Quote
Allspeeds Posted January 9 Author Posted January 9 2 hours ago, R1guy said: I believe Quist has an Efe head for sale Are handy il pm him thank you Quote
Allspeeds Posted January 9 Author Posted January 9 Dropped sump and oil filter cover off for vapour blasting with @Loudpipes tonight and dropped another batch of zinc off to be done small steps but progress non the less 1 Quote
Mar71n Posted January 12 Posted January 12 On 1/8/2026 at 7:03 PM, Allspeeds said: Marks been on he’s been making some bits past few weeks many of you will have seen his bits like this before but still nice Mark? Quote
Allspeeds Posted January 12 Author Posted January 12 8 hours ago, Mar71n said: Race component development OR RCD 2 Quote
baldrick Posted January 21 Posted January 21 He does some achingly beautiful stuff. I've a set of his rear sets on my zed/!gsxr. It's like art. Harris is taking shape nicely Quote
Allspeeds Posted January 24 Author Posted January 24 Got myself a complete EFE cylinder head and cams today all with be stripped and given to @Loudpipesfor vapour blasting before new valves and a port job I think happy to now have all the main components to build a nice engine over the next year 6 Quote
Allspeeds Posted February 3 Author Posted February 3 More small steps but gearbox is done made one out of 2 then had super finished bye FW development’s mates with brand new Suzuki bearings 5 Quote
clivegto Posted February 3 Posted February 3 2 hours ago, Allspeeds said: More small steps but gearbox is done made one out of 2 then had super finished bye FW development’s mates with brand new Suzuki bearings I had my turbo Harris gearbox supper finished and it's as slick as slick thing can be. Quote
Allspeeds Posted February 7 Author Posted February 7 @Loudpipesdropped my vapour blasting off this morning top job as always 0ff to paint and ceracoat next 7 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.