fatblokeonbandit Posted November 15, 2021 Author Share Posted November 15, 2021 Postman Pat has my chain and new rear sprocket.. Quote Link to comment
fatblokeonbandit Posted November 20, 2021 Author Share Posted November 20, 2021 New chain and rear sprocket 1 Quote Link to comment
fatblokeonbandit Posted November 20, 2021 Author Share Posted November 20, 2021 Now time to drill and tap the output shaft for the speedo rotor thingy 3 Quote Link to comment
fatblokeonbandit Posted November 20, 2021 Author Share Posted November 20, 2021 Bugger the cover won’t go on the rotor is to thick??? Better spin it in the lathe to slim it down 2 Quote Link to comment
clivegto Posted November 21, 2021 Share Posted November 21, 2021 10 hours ago, fatblokeonbandit said: Bugger the cover won’t go on the rotor is to thick??? Better spin it in the lathe to slim it down Put some spacers on the back. Quote Link to comment
fatblokeonbandit Posted November 21, 2021 Author Share Posted November 21, 2021 That Would mean spacing all the bolts, then the push rod would Be to short and there might not Be enough spline for the gear change ???? I’ll make the rotor smaller I think I had to do the same on me ‘arris when I did that 1 Quote Link to comment
jonny1bump Posted November 21, 2021 Share Posted November 21, 2021 I had do same turn it down. You done well drilling and tapping in situ. Quote Link to comment
fatblokeonbandit Posted November 21, 2021 Author Share Posted November 21, 2021 4 hours ago, jonny1bump said: I had do same turn it down. You done well drilling and tapping in situ. This is the 3rd one ive done in situ, they ends aren't hardened, just the working faces, or weren't in the 3 ive done, i used a lathe center drill to start then brand new 3,4 and 5mm drills from work, Dormer I think, good and sharp when new. 1 Quote Link to comment
jonny1bump Posted November 21, 2021 Share Posted November 21, 2021 I must got unlucky with last on i did as had use carbide in the lathe, but it did tap ok after so just must been hard spot after hearing about your results. Quote Link to comment
fatblokeonbandit Posted November 22, 2021 Author Share Posted November 22, 2021 (edited) Whizz Whizz, thast better.... cover goes on now we have some clearance Clarence.. and it only bleedin works.. Edited November 22, 2021 by fatblokeonbandit 3 Quote Link to comment
fatblokeonbandit Posted November 22, 2021 Author Share Posted November 22, 2021 (edited) cover on and the clutch works as well!!! Edited November 22, 2021 by fatblokeonbandit 4 Quote Link to comment
fatblokeonbandit Posted November 23, 2021 Author Share Posted November 23, 2021 Just a thought???? 1 Quote Link to comment
fatblokeonbandit Posted November 23, 2021 Author Share Posted November 23, 2021 got some 6m ID ally tube from B&Q to make some bars to tidy up the coolers.. £7.. 7 Quote Link to comment
wraith Posted November 23, 2021 Share Posted November 23, 2021 What size/length push did you use for the push rod? Quote Link to comment
fatblokeonbandit Posted November 23, 2021 Author Share Posted November 23, 2021 I'm measure it tomorrow matey 1 Quote Link to comment
fatblokeonbandit Posted November 24, 2021 Author Share Posted November 24, 2021 22 hours ago, wraith said: What size/length push did you use for the push rod? 80 mm 1 Quote Link to comment
fatblokeonbandit Posted November 28, 2021 Author Share Posted November 28, 2021 modern foot pegs from a Busa, and messing with various gear levers to sort the stupid 1 up 4 down.... then the penny dropped with a big clang!!!!!!! 5 Quote Link to comment
fatblokeonbandit Posted November 28, 2021 Author Share Posted November 28, 2021 and modified boots for stick coils 5 Quote Link to comment
jb Posted November 29, 2021 Share Posted November 29, 2021 (edited) 17 hours ago, fatblokeonbandit said: modern foot pegs from a Busa, and messing with various gear levers to sort the stupid 1 up 4 down.... Worked as standard with the 750 motor. Edited November 29, 2021 by jb 1 Quote Link to comment
fatblokeonbandit Posted November 29, 2021 Author Share Posted November 29, 2021 I tried it that way JB, but I prefer the look of the small lever pointing up but that makes up side down changing ? All sorted now anyway … need to get it finished before the mot runs out so I can try it out, really looking forward to riding it 1 Quote Link to comment
fatblokeonbandit Posted December 4, 2021 Author Share Posted December 4, 2021 I wife’s always said she wishes I had a nine incher.. 4 Quote Link to comment
fatblokeonbandit Posted December 4, 2021 Author Share Posted December 4, 2021 Look ok I think 6 Quote Link to comment
TonyGee Posted December 4, 2021 Share Posted December 4, 2021 looks good to me, when its pointing at the road 1 Quote Link to comment
fatblokeonbandit Posted December 6, 2021 Author Share Posted December 6, 2021 Bought a spare front wheel which happens to be silver so stuck it in to see what it’s like, and squirted some white paint on the mudguard 7 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.