paddle Posted July 6, 2020 Share Posted July 6, 2020 Hi guys and girls this problem with my 1200 inazuma is doing me in.statred it tonight very reluctant then start then for ten minutes it was bellowing out a smoke and petrol smell strange thing it was ticking over just fine and revved up fine but the smoke smelled so rich I've just replaced the carb needles with genuine suzuki items just last week,and when I turn it off petrol is oozing from the back of number 2 carb.is there anyone on here who can rebuild carbs and test them I got three other projects on the go that all will need rebuild kits I'm a man on the edge Quote Link to comment
Gixer1460 Posted July 6, 2020 Share Posted July 6, 2020 Sounds like you need a tap repair kit as well as smokey and petrol smell may indicate fuel in the oil / crankcase - have a sniff in the filler hole? Quote Link to comment
paddle Posted July 6, 2020 Author Share Posted July 6, 2020 The tap is working fine and I dont seem to have any fuel smell from my filler hole I think the fuel leaking from the rear of the carb is what's left in the fuel pipe it just over fuels really bad when its running Quote Link to comment
Svsam Posted July 7, 2020 Share Posted July 7, 2020 Sounds like float needle stuck open on number 2. that’s what I find 9 times out of 10 when there’s fuel coming out the filters. This will also over fuel more than likely causing the smoking petrol smell. 1 Quote Link to comment
paddle Posted July 7, 2020 Author Share Posted July 7, 2020 Well got home from work went in the garage total chaos air box full of fuel,cylinders full of fuel,and sump full of fuel with that much leakage the fuel tap must be faulty.I have ordered a repair kit plus an extra stand alone hi flow vacuum fuel valve plus a set of genuine suzuki float valves as when I checked the originals they all had a wear ring in the rubber cone and the little sprung loaded post on a couple was getting stuck.lets hope I've got it sorted Quote Link to comment
Tombola Posted July 7, 2020 Share Posted July 7, 2020 Check your float heights. Do you know what carbs they are? Quote Link to comment
paddle Posted July 7, 2020 Author Share Posted July 7, 2020 CVK 32 Keihins on the inazuma 1200 Quote Link to comment
Reinhoud Posted July 8, 2020 Share Posted July 8, 2020 Hold the carbs up side down and blow through the fuel line, if you can blow through one of the float needles is leaking. 1 Quote Link to comment
Dezza Posted July 8, 2020 Share Posted July 8, 2020 (edited) Sounds like a good excuse to source some bigger replacements for the stock bonsai carbs Edited July 8, 2020 by Dezza 1 Quote Link to comment
Dukeman Posted July 8, 2020 Share Posted July 8, 2020 I had the same, new needle and seat purchased, I purchased a new tap thinking it was that, but NO. I have not fitted them yet, that is a job to do soon. Quote Link to comment
paddle Posted July 8, 2020 Author Share Posted July 8, 2020 I've replaced the float valves did a bench test with about 200ml of fuel all good after 2 hours.i think the tap is intermittently working so will replace the diaphragm in that as well Quote Link to comment
Dukeman Posted July 9, 2020 Share Posted July 9, 2020 (edited) From experience you want to have a tank above the carbs to replicate the pressure from the tank with gravity / pressure. I did a small fuel test and the needle and seat where fine, I put a lawn mower tank hanging above the carbs filled with gas and they leaked. Edited July 9, 2020 by Dukeman Quote Link to comment
BanditStates Posted November 1, 2020 Share Posted November 1, 2020 On 7/9/2020 at 9:26 AM, Dukeman said: From experience you want to have a tank above the carbs to replicate the pressure from the tank with gravity / pressure. I did a small fuel test and the needle and seat where fine, I put a lawn mower tank hanging above the carbs filled with gas and they leaked. How did you fix? Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.