Jump to content

Srad 750 Gsxr1000 Engine Swap


Recommended Posts

Dunno if anyone has done this one here before but maybe usefull to someone

Started today with an engineswap, a K4 thou is transplanted into a 96 srad 750. Front end will be mounted too.

I started out with a complete Srad 750 and a Complete damaged K4 Thou engine with loom exhaust etc etc all what’s needed to get it running.

So first butchered the thou and then the Srad took out everything wich i didn’t need anymore.

Welded the bottom of the thou tank into the Srad tank as i need the thou fuelpump for EFI.

Getting the thou engine into the Srad is quite easy you need to take of 6mm of the lower engine mounts on both sides wich i did using an anglegrinder and a Dremel as usual.

The upper engine mounts need to be taken away to make room.

Engine is now in place chainline is spot on.

Next is creating new enginemounts for the upper and cilinderhead mounts.

Bought some steel today so will start tomorrow on that.

Will keep you updated on progress.

 

730EE43C-7DC6-4DA8-8819-273F31249290.jpeg

6CCAF3CC-86E9-4B47-A883-8BFF29836148.jpeg

EE69B55D-5962-4D44-9388-79952D9202F2.jpeg

2DD0645D-2807-4272-819E-A64F26ADC642.jpeg

083B8C1F-90CD-4A37-A7D9-60DC60812BB8.jpeg

243CF381-A22E-4C85-AC5F-3EE5232D6C7E.jpeg

EB6FE557-10A4-4ABA-BC8A-5035740D0547.jpeg

3B53B80C-DBE0-46F2-A410-1EC26608ACB9.png

  • Like 12
Link to comment

Today i made all the enginemounts out of 4mm steel, took more time then i thought as usual.

The engine sits spot on exhaust line is perfect

Will spray them Silver to hide them a bit.

Happy with the results till now

Next stop is bolting radiator loom airbox tb’s in place 

373FF327-6B5D-47F6-9920-FEEED5A4D5CA.jpeg

08ADB074-4835-4BAF-8C09-2F61D481543C.jpeg

3BABB798-79E7-483B-99EE-C827A865CEE9.jpeg

B20D0EBA-FC68-414E-9CEE-69479EC12083.jpeg

9A1368B6-80A0-48EC-937E-5482CDCF39B6.jpeg

93110F18-F86B-4FA3-BE49-C3CF0FC34CAA.jpeg

04977617-1BFD-43DE-A5E1-D54AB02132E0.jpeg

88CBD122-DF1A-43FB-B42E-601A6F6CC422.jpeg

  • Like 7
Link to comment

Nice build! Will it be another trackbike?

Started today with an engineswap, a K4 thou is transplanted into a 96 srad 750. Front end will be mounted too.

Do you want rid of the Srad forks? :vu:

Edited by TLRS
I'm a tnuc
Link to comment
31 minutes ago, KATANAMANGLER said:

Sander, you are always the pioneer and you are a credit to OSS. I will watch on with interest.

Not the pioneer as you say, it has done before by others.

But i will happily take your compliments it still is a lot a work and thinkwork to get this done.

Thanks !!

  • Like 2
Link to comment
  • 2 weeks later...

Wasn’t allowed to work on the bike because of a fracture in my elbow for a week to see how it healed.

So all good now and back to work.

Decided to hacksaw the thou airbox to make it fit wich worked the intakes are under a different angle so chopped them off and glued some foam to the frame for final fitment. Also made a new bracket to mount to the frame.

Now working on getting the thou loom into the frame wich works pretty good i can use the space where the cdi was for the ecu starterrelais etc only have to find a new place for the rectifier.

I have some plugs left on the loom wich i really don’t have a clue where there from so have to figure that out also.

So have to mount everything next is getting the k4 front end in.

 

 

7F4C08EB-3C7D-4F3B-A3C6-553C14B1F8D2.jpeg

56B253E6-5568-46EA-89B6-AA92F4165C9F.jpeg

7321192F-6B4B-4AF5-969B-4F1E8DF16386.jpeg

44129F54-0D42-4A42-8E0F-5AC11085FF7C.jpeg

  • Like 1
Link to comment

Front end sorted thanks Suzuki ! 1 on 1 swap also purchased some R6 calipers. Need to measure if the srad discs fit the k4 wheel as they are bigger wich i like.

 

Also found out the plugs i couldnt work out are for the exhaust servo motor wich i don’t use so sorted

B342AFB4-CCC1-485C-875C-7F8B66049C39.jpeg

7CE67B71-D434-4E3F-B2EB-7259C3839415.jpeg

Edited by Leblowski
  • Like 2
Link to comment

Got my Battery so checked systems all seems fine, now fill er up with oil gas and liquid then an attempt to fire her up.

In the mean time i trimmed the fairing to suit.

A bit of hacksawing here and there but nothing big need to create new lower mount on the engine thats it.

It al fit’s nice and tight.

Found out the srad 320 discs fit the k4 wheel srad wheel doesn’t it’s approx 1 cm wider so i will stick with the k4 wheel

Tried to fit the k4 rear also, it fits like a glove all bushes spacing etc is excactly the same however the chain is not alligned and can’t mill anything of the wheelcarrier as there’s no meat so the srad wheel will stay.

C33E2BF2-5A8B-4CD7-BEF9-723856E3AE35.jpeg

0C0EBB79-EDCB-4AB0-BA26-44BF85D3FC33.jpeg

D657D3B7-3AE1-45C9-A7D4-E7E7D3428019.jpeg

72352407-BC2A-4481-B874-18AF554F77B7.jpeg

E4154731-031A-4D70-8D57-8AFD7EF188B1.jpeg

  • Like 7
Link to comment
9 hours ago, Leblowski said:

Found out the srad 320 discs fit the k4 wheel srad wheel doesn’t it’s approx 1 cm wider so i will stick with the k4 wheel

Srad wheel should have a 130mm wide hub. Many later gsxr's have 128mm hub so that shouldn't be the issue? Srad fork spacing is 214mm while later gsxr's have 207mm. Either way you probably need either different yokes or space the discs out. Or fit Brembo sbk discs with the appropriate offset.

Link to comment

Rearsets arrived today as always good quality for a good price, the mastercilinder needed some tweaking to get it all alligned proper.

The rearcaliper was shot but i had a k2 600 caliper if i am correct wich bolted right on.

Coming weekend will be a bit trilling, first start up so will know if the engine seller wasn’t lying O.o as i never heard the engine running

3A108660-A096-4A74-BE1E-AEDB07E4972A.jpeg

  • Like 5
Link to comment
  • 2 weeks later...

Got the bike out yesterday and tried to start it wich it did, for about 3 seconds.

After some googling i found out these bikes have a tip over sensor wich wasn’t mounted right.

So got that sorted and presto instant fire up and idling the engine revs nice but was a tad smokey could be the oil i pored into the cilinders or the two stroke oil i used after elektrolysis.

Started the bike up end of the day again and smoke was about 80% less so i think i am fine.

Need to sort the oilleaks, frontbrakes, chain and suspension needs setting up.

So almost there

  • Like 5
Link to comment

Front end done made some brackets for the srad fender to suit.

Also welded a new bracket on the front end wich was broken very happy welding went easy.

Next is putting some slicks on and waiting for some brakelines from @gsxr884/ cp racetec so front end will be finished besides suspension

Been at hyperpro last week they will do some upgrades on the rearshock front end will get some skf green seals for less friction wich i will install myself to keep the cost down.

I need to change gearing on the bike so i will convert it to a 520 chain and sprockets also.

The completion of this project is in sight !

 

F65BE51F-5FC7-4824-9027-E2EECD5E5769.jpeg

  • Like 3
Link to comment

Always did my front end overhauls my self but did it with homemade tool wich where put together in the time i couldnt weld myself

So it was time to create a proper one two hour job to create this tool to compress the forks so top can be taken of.

Forkoverhaul next will be installing some skf green forkseals wich will give less friction and will last langer as some may say .

047B7A0E-6201-4724-AB58-75DE5A007DDC.jpeg

49C56C01-6D43-4357-85C1-6968F767F5EA.jpeg

Edited by Leblowski
  • Like 3
Link to comment

Excellent build and bike looks factory made so proper sleeper. Give them 1000 riding boys a surprise.

Hope theres a vid once is all finished

I remember Years ago a Swedish blokes bike  in PB or Streetfighter mag doing similar engine swap to a 600 Srad. He actually cut engine mounts off 1000 frame and welded in place on 600. He said hardest part was welding the radial brake mounts onto standard SRAD 600 forks. getting them aligned etc. Wish I still had the mag

Edited by GS1000 78
Link to comment
7 hours ago, GS1000 78 said:

Excellent build and bike looks factory made so proper sleeper. Give them 1000 riding boys a surprise.

Hope theres a vid once is all finished

I remember Years ago a Swedish blokes bike  in PB or Streetfighter mag doing similar engine swap to a 600 Srad. He actually cut engine mounts off 1000 frame and welded in place on 600. He said hardest part was welding the radial brake mounts onto standard SRAD 600 forks. getting them aligned etc. Wish I still had the mag

I could have done the same with the framemounts as i had the k4 thou frame too but choose not to so i could always mount the 750 engine when needed.

Welding radial brake mounts on a srad 600 fork ! I would like to see some pictures:)

Link to comment

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...