Jump to content

Jeb

Members
  • Posts

    56
  • Joined

  • Last visited

Everything posted by Jeb

  1. Jeb

    Shock length

    God bless ya Cheers
  2. Jeb

    Shock length

    Hi, Anyone know how long (eyelet to eyelet) a early hyabusa rear shock is?...having trouble sourcing a decent one for my 1100f, though there are loads of hyabusa ones. Cheers
  3. Jeb

    Gaskets

    Cheers, will check out
  4. Jeb

    Gaskets

    Thanks... I think that's probably the best thing to do, cheers
  5. Jeb

    Gaskets

    Hi, ...can anyone reccomend a pattern top end gasket set for an 1100f. Cheers
  6. Jeb

    Engine year

    Ah, get it ...cheers!
  7. Jeb

    Engine year

    That's great, cheers
  8. Jeb

    Engine year

    Hi, My 1127 motor has the no v706 1033** Anyone know roughly what year this is from. Cheers
  9. Jeb

    Compression test

    Haha, yes......its been standing a few years .....only cost £100...so no probs...the more I turn it over the better it gets.....will do valve clearances and see whether there's any difference took a punt on it as it was cheaper than getting 2nd hand barrels...I can always turn it into an anchor for my other bike...
  10. Hi, ....does anyone know if tight, or loose valve clearances would account for dodgy compression ? Thanks in advance
  11. Jeb

    Gsx1100f engine

    Hi, Sorry I was unaware of the 50 posts rule
  12. Jeb

    Oil cooler

    Hi, I'm after a replacement oil cooler for my 1100f...does any other models' fit or has anyone tried a Chinese one and if so where can I get one from. Cheers
  13. Jeb

    Exhaust gaskets

    Thanks chief, have done and am sorted
  14. Jeb

    Exhaust gaskets

    Hi, I need some new exhaust gaskets for my 1100f....there's a mixture of types on ebog, but the existing ones are about 4 to 5 mm thick and seem to be made of lots of small strands of copper wire....can these still be obtained or do any of the other types work? Thanks
  15. Jeb

    Brake calipers

    Thanks for all advice, I already have braided lines but will try the sbs pads before anything else cheers....will check out post
  16. Jeb

    Brake calipers

    Hi all, Is there an easy, ie, direct fit , to replace the front calipers on a gsx1100f. ..I've heard others fit without any mods.... Cheers in advance
  17. Jeb

    Exhaust stud

    Might try a bit of heat beforehand to see if this helps.....all the other bolts were stainless and came out easy. I'm cursing the turd who put in a normal one..
  18. Jeb

    Exhaust stud

    Hi all, has anyone used left hand drill bits to remove a sheared exhaust stud......I'm reluctant to use 'easy outs' as I had one snap on me on another bike and they are undrillable! Thanks in advance
  19. Jeb

    Exhaust bolts

    Good point, thanks
  20. Jeb

    Exhaust bolts

    Thanks, Stainless seems the way to go!!
  21. Jeb

    Exhaust bolts

    Hi all, Just after a bit of advice....what type of header pipe bolts should I replace my existing ones with...or is it better to put in some exhaust studs . It's an 1100f. Thanks
  22. Jeb

    Exhaust

    Thanks, that's bloody great...gives me more options....I'm loathed to spend too much as I only paid 350 for the bike . ...
×
×
  • Create New...