Jump to content

cbr2gsxr

Members
 View Profile  See their activity

  • Posts

    16

  • Joined

  • Last visited

Reputation

4 Neutral

Personal Information

  • Location
    Sarasota, Florida USA

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. cbr2gsxr
    Cool, thanks guys.
  2. cbr2gsxr
    Will an RF900 front wheel fit a 91 GSXR 750 without modifications?
  3. cbr2gsxr
    .Has anyone on here installed a set of FCR's on a GSXR 1100 and if you have what jetting are you using. I have a set I am trying to use and just want to get an idea of baseline jetting to get me close. Any help would be greatly appreciated
  4. cbr2gsxr
    Sheep, DO NOT run your A/F screws to 1.5 turns out, you will flood the plugs at idle. 1/2 turn and leave it until you get float height set. Its popping because the plugs are fouled and cylinder is not firing. Put in all new plugs, turn to 1/2 and fire it up!
  5. cbr2gsxr
    Sheep, if you are running RS36 carbs and they are out of sync, they will never run right. Also, I have found that if RS carbs run rich, you will not get a cylinder to fire. How did you sync them? Bench sync? What are your A/F screws set too? Float height is very critical with these carbs. Mine are not at 17mm more like 19 to get it from running rich even with stock jetting. Did this start to happen after you swapped out the 40's for the 36's? Take a look at your slides, make sure they are all even at the bottom of the slides.
  6. cbr2gsxr
    Meanbean49, did you use the adapter plate? I like those dogbones. Great idea.
  7. cbr2gsxr
    CoRSJohnny, check and make sure you have a good ground connection coming from the battery to somewhere on the frame. I bad ground or loose ground can have adverse affects on the CDI!
  8. cbr2gsxr
    Wimbaas, I am buying the adapter. Exactly how do they bolt in? I see where the bolt goes through, but the plate behind it has 2 holes. Do those bolt to the frame?
  9. cbr2gsxr
    Wimbaas, I am going to buy them from him. I juse sent him a private message on currency. Not sure if it is GBP currency.
  10. cbr2gsxr
    Davecara, LMAO! Just opened my first beer. I tried using the Busa knuckle and its not the shock that is the issue is the actual position of the dog bones. They are almost horizontal with the swing arm. I tried a Busa knuckle, Srad knuckle and a Bandit knuckle. Just cant get the correct angle. It is almost like have a strut on instead of a shock.
  11. cbr2gsxr
    I was told their is an adapter plate that was designed by someone on OSS that will allow me to install a Hayabus swingarm on my 91 GSXR 750. Please, if anyone knows anything about this or has one, please, please let me know. I am stuck and need help!
  12. cbr2gsxr
    Wimbass, what adapter plate, please pass it on to me! I am in dyer need!
  13. cbr2gsxr
    Fula28, I am using the 750 linkage. Did you mean use the Busa linkage?
  14. cbr2gsxr
    I am trying to install a 1st Gen. Hayabusa swingarm on my 91 GSXR 750. I am trying to use my 750 linkage knuckle, but when I put the dogbones on I get ZERO suspension travel because the dogbones are too horizontal. I have the Busa one, but it is not as wide as the 750 one and the bolt on my 750 to attach to the frame is a larger diameter than the busa one! Not sure what to do! Please help!
  15. cbr2gsxr
    Hey guys, first time poster! I just dropped in a 2002 Bandit 1200 motor into my 90 750 frame. Where does the Orange and black wire from the alternator plug go to on my 90 750 wire harness? I have 2 wires coming off of the GSXR wire harness, one red and one orange! Not sure which one to splice into! Any help would be greatly appreciated!
×
×
  • Create New...