-
Posts
85 -
Joined
-
Last visited
Reputation
64 ExcellentAbout alfiestorm
- Birthday 03/05/1964
Personal Information
-
Location
costa del south coast portsmouth
Recent Profile Visitors
The recent visitors block is disabled and is not being shown to other users.
-
Been busy, fitted new chain, ultra sonic cleaned the carbs and set them up to factory spec and gave it a bit of a tune up and now running very nice. Gave it a bit of a polish up too came up quite good for original paint. First video is how it was with leaky carb and running quite rough. Second video is it running after I had ultrasonic cleaned the carbs and tune it up, running spot on.
- 1 reply
-
- 2
-
Awesome 2-Stroke Pics
alfiestorm replied to banoffee's topic in Water Cooled, V-Twins, Singles and 2-strokes
-
Got it for 2.5k off a mate. 11k miles imported from Canada. Very good I think condition for an original unrestored bike. Getting it registered and do a few bits and bobs to it and enjoy it on the road
- 1 reply
-
- 6
-
One off of a bandit 6 or 1200 will do it.
-
Not enough charge going into the battery maybe or a broken wire in the loom near the engine, loom warms up flexes bike cuts out bike cools down loom wire makes connection bike starts and so on? or cdi breaking down when it gets warm I have had that happen before and was a bugger to track down to the cdi, or starter solenoid playing silly buggers .
-
Looking to change the two pot standard caliper for a four pot caliper. I measured the mount centres with a rule and came out at 73mm my old eyes were telling me, theres plenty of room for a four pot and will miss the spokes easily as the old two pot caliper is very wide compared to more modern four pot calipers. Has anyone put a four pot caliper on that bolted straight on, if so what caliper did you use from what bike. It's the single front disc model on the left hand side and pretty much useless on todays roads. Thanks in advance.
-
Slingshot 1100 RS38's setting might help out some
alfiestorm replied to alfiestorm's topic in Oil Cooled
I would recommend getting it dyno'd, at least then you will know the true power of the bike and the mixture settings through the rev range will be good and safe. Cost me £185 to have it set up on the dyno. -
Slingshot 1100 RS38's setting might help out some
alfiestorm replied to alfiestorm's topic in Oil Cooled
152 at the back wheel and 90ftlbs of torque -
Thought I would share carb settings of my Mikuni RS38's for anyone that may have a similar setup to my bike. The bike a GSXR1100L 1990 it has, gas flowed head, Wiseco 1216 kit, Kent cams suited to the gas flow and big bore, Cobra stainless steel big bore down pipe exhaust system original 1990's system too. Carb settings Main jets are 140's Pilot jets are 17.5's and the fuel mixture screw is set at half turn out. This may help anyone with RS38's with a similar setup to my bike at least a base line to work from.
-
old age spots, never seen them before, Might be worth investigating further in case its something special from the factory maybe, or might just be lumps left over from someones idea on something.
-
RG250 MK1 swingarm swap?
alfiestorm replied to alfiestorm's topic in Water Cooled, V-Twins, Singles and 2-strokes
Not yet, getting into the bike at the weekend. -
I am working on a mates rg250 with him and doing a oily rag restomod on it, We have a complete Yamaha R1-Z250 front end to go on to get shot of the standard 16" wheel and crap brake set up so the front is sorted. Left us thinking about the back end and their is not a lot of room to fit anything bigger than a 120 tyre in there. Would anyone know if a swingarm off of an RGV VJ21 will fit in the RG frame ? or any other swingarm that will allow a 17" x 4 or 4.5" rim and a 140/150 section tyre. Something I just remembered is the original rear wheel is an 18" so maybe a 17" wheel will allow a 140 section tyre as it will sit further back in the standard swing arm? Any ideas or advice will be much appreciated.
-
They went to power valve motors in 1985, Suzuki called their system SAEC which I think although not 100% sure stands for Suzuki Advanced Exhaust Control
-
Ignitech programable ignition system maps. Spit back through carbs.
alfiestorm replied to alfiestorm's topic in Oil Cooled
I have sorted it out it was indeed what dupersunc said weak mixture at low rpm's, I used a colour tune set to get it right. Relieved it was just that and didn't have to go further into the engine. The screws are less than a quarter turn out and they were half turn out so these carbs are quite sensitive to adjustments on this fuel mixture screw. Thanks for all you advice chaps much appreciated. -
Ignitech programable ignition system maps. Spit back through carbs.
alfiestorm replied to alfiestorm's topic in Oil Cooled
What dupersunc said about weak low rpm mixture got me thinking. When I fitted the overhaul kit to the carbs it came with new fuel mixture screws with all the needle like ends the same length and the ones I took out were all different lengths due to wear over the years. I set the new ones to what the old ones were set to. Will put the colour tune on later today to see what the burn is and set it with that and see what happens.