Jump to content

Magoo

Members
  • Posts

    62
  • Joined

  • Last visited

Reputation

34 Excellent

Personal Information

  • Location
    UK

Recent Profile Visitors

806 profile views
  1. My apologies, I was well into my cups when I wrote that.
  2. Get some squishy foam filters and you should be OK.....though on a bandit, the carbs can foul the fuel tap. I'm not sure if this will be an issue on your bike (coz I don't think you told us what bike it is)
  3. You may not need to grind the alternator bit with the dot head on as this will raise the carbs by a noticeable amount.
  4. The wheels are from a mk2 bandit 1200 (though I don't think there's any difference between mk1 and mk2 wheels besides the spoke pattern) The slingshot has a quite large spacer on the caliper side that covers the bearings whereas the bandit has a top hat spacer that fits inside the bearing seal (slingshot doesn't have a bearing seal). The difference between these spacers' widths appears to be the same as the difference in caliper hanger width on the spindle. Bandit - narrow spacer & wide caliper hanger : Slingshot - wide spacer & narrow caliper hanger I think my sprocket carrier is the stock gsxr one, though it was ages ago when I fitted it and I may be mistaken (as for the spacer inside the sprocket carrier, I have no clue which is in there but it fits well (It's either a B12 or a 1100L) Disclaimer : My gsxr was a 26 years old bitsa when I got it and what I think was standard fit may not be. My swingarm is a metmachex but I'm assuming that the rear spindle width would be the same as a stock one
  5. I have bandit wheels in my 1100l. I used the bandit RHS spacer and the slingshot LHS spacer and the rear lines up nicely (sprocket bolts are very close to swingarm but not contacting.) ...with bandit caliper hanger
  6. I just wedged a load of bits of pipe insulation down between the lamp bowl and the rearmost plastic housing (4 on 'fiche) It stopped the bowls rattling about and the lights are pointed forwards still. (My adjusters will just fall to bits if I try to move them.)
  7. Mk2 has pairs valve ports on the front of the block, and a threaded output shaft for the speedo sensor. I can't think of any other differences (other than carb spacing but this is changed with inlet rubbers - the heads are the same) *to the best of my limited knowledge
  8. My 1100L has dipped and main (and side) on both lamps.
  9. It was the sidestand switch. Right on the money Wee Man. Cheers, I owe you a beer.
  10. Thanks for your input guys, much appreciated. Funny you should mention the sidestand switch. It's been pretty flakey for a while now. (Sometimes I have to kick the stand in hard for the bike to allow me to leave. (Was thinking to bend the tab on the stand out a bit to ensure switch depression....but I always forget when getting home) Tomorrow I'll take it somewhere quiet so as not to irritate the neighbours and see if I can make >7krpm in neutral. (Will do a wiring check 1st) Many thanks.
  11. Hi folks, Having spent some time in Antarctica for work, and then getting home just in time for this poxy lockdown, my bike got it's 1st run out in months today. It runs nicely up to just under 7k rpm, then pops a loud bang, rev counter reads at zero for a second (with total loss of power), then the bike continues running until Near 7k rpm when it does the same...every time. I plan to have a look at my valve clearances tomorrow. Can you suggest any other constructive avenues of inquiry? (1990 GSXR1100L) Cheers, Magoo.
  12. Yes indeed. That looks mint.
  13. That all makes sense now. I hadn't considered adding extensions to the swingarm shock mounting. Cheers, mate.
×
×
  • Create New...