Jpich85 Posted May 25, 2017 Share Posted May 25, 2017 After changing the bearings on the front wheel one of the bearing housings seem to be too large to press fit the bearing in :-(, I think I'm going to need a new front wheel but wanted to ask where would be the best place to buy one as there's not much on Eblag atm. Cheers Quote Link to comment
SiBag Posted May 25, 2017 Share Posted May 25, 2017 Put a request in the wanted section, you might be lucky. 1 Quote Link to comment
Jpich85 Posted May 25, 2017 Author Share Posted May 25, 2017 Thanks mate I'll give that a try, Has anyone used that bearing retainer loctite stuff, not sure if I should use that for now? Quote Link to comment
Gammaboy Posted May 26, 2017 Share Posted May 26, 2017 WN used the same front wheel as the L/Ms - any of the curved spoke 3.5" front wheels will do it. Quote Link to comment
busa1300 Posted May 26, 2017 Share Posted May 26, 2017 (edited) I had that issue with a front wheel before. Bearing just fell in......so I took a center punch and dimpled the inside of the face where the bearing fit into. Has been working fine for years now. Edited May 26, 2017 by busa1300 1 Quote Link to comment
Gammaboy Posted May 26, 2017 Share Posted May 26, 2017 (edited) The other option is loctite bearing retainer. not personally used it, but i know people who have. Edited May 26, 2017 by Gammaboy 1 Quote Link to comment
Jpich85 Posted May 26, 2017 Author Share Posted May 26, 2017 Thanks guys, busa did you center pop all around the bearing housing or just a few here and there, I've got some bearing retainer coming so I might try busas idea with the loctite, it's a shame coz I've just had it powder coated and decaled up lol Quote Link to comment
Fazz711 Posted May 26, 2017 Share Posted May 26, 2017 Use lots of small dot marks evenly spread around the housing and a small amount of bearing retaining fluid. It's a bit of a bodge but will work if you are careful. Quote Link to comment
Jpich85 Posted May 26, 2017 Author Share Posted May 26, 2017 Thanks mate, I know I'm a bit worried coz it is a bodge and I don't really like doing work like that but if I use it until a get a new wheel hopefully it'll be ok, I get a bit depressed when the bikes off the road Quote Link to comment
busa1300 Posted May 26, 2017 Share Posted May 26, 2017 If you dimple on the inside of the wheel, you'll never see it once the bearing is in, should not be a problem with the Powdercoat. Only should take maybe 6-8 hits evenly around bearing mating surface...if the bearing just barely slides in now, it won't take much to get it tight. 1 Quote Link to comment
Jpich85 Posted May 26, 2017 Author Share Posted May 26, 2017 Thanks busa I'll give that a try tomorrow and hopefully get it right 1 Quote Link to comment
Madb Posted May 28, 2017 Share Posted May 28, 2017 if you get stuck for a wheel pm me. i reckon you should be ok tho once you dimple the face but if not pm me. 1 Quote Link to comment
kja.busa Posted May 28, 2017 Share Posted May 28, 2017 I thiunk I've got a 750L front wheel in the shed if you need one, but sounds like youre sorted. 1 Quote Link to comment
Jpich85 Posted June 7, 2017 Author Share Posted June 7, 2017 Thanks guys I've sorted it now I feel comfortable that it'll hold well but that's for you're help :-) 1 Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.